Operation - Scheppach dp13 Traduction Du Manuel D'origine

Installing the chuck, Fig. 8
1. Clean the conical hole in the chuck (5) and the
spindle cone with a clean piece of fabric. Make
sure there are no foreign particles sticking to the
surfaces. The slightest piece of dirt on any of these
surfaces will prevent the chuck from seating pro-
perly. This will cause the drill bit to wobble". If ta-
pered hole in the chuck is extremely dirty, use a
cleaning solvent on the clean cloth.
2. Push the chuck up on the spindle nose as far as it
wiII go.
3. Turn chuck sleeve anticlockwise (when viewed
from above) and open jaws in chuck completely.
4. Place a piece of wood on the machine table and lo-
wer the spindle onto the piece of wood. Press firmly
to ensure that the food sits exactly.
Fastening radial drill press to supporting surface
For your own safety, it is highly recommended to ins-
tall the machine on a bench or similar.
WARNING:
All the necessary adjustments for the good working of
your drill press have been done at the factory .Please
do not modify them.
However, because of a normal wear and tear of your
tool, some readjustments might be necessary .
WARNING:
Always unplug our tool from power source before any
adjustment"
Quill return spring, Fig. 9
It may be necessary to adjust your quill return spring
if the tension is such that the quill returns either too
rapidIy or too slowly
Lower table for additional clearance.
1
Work from left side of drill press.
2
Move the stop nuts (B) down to their lowest posi-
3
tion and lock in place with wrench to prevent quill
dropping while tensioning spring.
4 Place screwdriver in lower front notch (C) of spring
cap (D), and hold it in place
Remove the screw (E) and the knurled nut (C) by
5
using an Allen wrench (SW5).
Carefully turn screwdriver anticlockwise and engage
6
next notch in boss (G). Do not remove screwdriver.
7 Install the knurled nut (C) and the screw (E) again.
8 If there is not enough tension on spring, repeat
steps moving onIy one notch each time and
checking tension after repetition. Proper tension is
achieved when quill returns gentIy to full up position
when released from 20 mm-3/4" -depth.
Check quill while feeding to have smooth and unre-
9
stricted movement. If movement is too tight, loosen
allen screw (E) and knurled nut (F). Check if the
spindle can move freely again. Retighten jam nut.
The angular play of the spindle. Fig. 10
With the spindle in a low position, take it in your hand
and try to make it revolving about its axis. If there is
too much play, proceed as follows:
1 Loosen lock nut (L).
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Turn the screw (I) clockwise to eliminate the play
2
but without obstructing the upward and downward
motion of the spindle (a little bit of play is normal).
Tighten the lock nut.
3

8. Operation

WARNING:
if you are not familiar with this kind of machi-
ne, take advice from an experimented person.
In any case you should have read and understood the
safety and operational instruction before attempting
to operate this product.
Pivoting the table, Fig. 11
To bring the table (3) to the inclined position, re-
1
lease the table locking (h) and adjust the desired
table angle. Re-tighten the table locking
Adjusting table height., Fig. 12
1 Loosen the table support lock handle (b).
Adjust the table (3) to the desired height.
2
3 Re-tighten the table locking (b).
Note: it is better to lock the table to the column in a
position so that the tip of the drill bit is just slightly
above the top of the workpiece
Installing drill bits
Inser1 drill bit intc chuck (A) far enough to obtain
1
maximum gripping of chuck jaws (B). (When using
a small drill bit do not insert it so far that the jaws
touch the flutes -spiral grocves -of the drill bit. )
2 Make sure that the drill bit is centered in the chuck
before tightening the chuck w th the chuck key
(C). optional.
Tighten the drill chuck sufficiently, so that the drill
3
bit does not slip while drilling.
Turn the chuck key clockwise to tighten, anticlock-
4
wise to loosen. Tighten the drill bit equally by using
all three holes in successicn. The drill bit can be
release by using one hole only.
Choosing speed and tensioning belt, Fig. 13
Note! Pull power plug!
You can set different spindle speeds on your pillar
1
drilling machine:
2 WITH THE SWITCH „OFF", open pulley cover.
Loosen the drive belt on the right side of the ma-
3
chine head by unfastening the wing screws (12)
on both sides. Pull the right side of the motor in the
direction of the spindle to loosen the v-belt. Tighten
the wing screws again.
4 Attach the v-belt to the corresponding belt pulleys.
5 Loosen the wing screws and push the right side
of the motor backwards to clamp the v-belt again.
Tighten belt tension lock knob. Belt should deflect
6
approximately 13 mm –1/2" -by thumb pressure at
mid-point of belt between pulleys.
7 Close pulley cover .
8 If belt slips while drilling readjust belt tension.
GB
23 / 44