Introduction; Device Description; Scope Of Delivery; Intended Use - Scheppach dp13 Traduction Du Manuel D'origine

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
We hope you have a lot of fun and success using your
new machine.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• improper handling,
• noncompliance of the operating instructions,
• repairs by third parties, not by authorized service
technicians,
• installation and replacement of non-original spare
parts,
• non-intended use,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
that you read through the entire operating instruc-
tions before putting the machine into operation.
These operating instructions are to assist you in get-
ting to know your machine and utilize its proper ap-
plications. The operating instructions contain impor-
tant notes on how you work with the machine safely,
expertly, and economically, and how you can avoid
hazards, save repair costs, reduce downtime and in-
crease the reliability and service life of the machine.
In addition to the safety requirements contained in
these operating instructions, you must be careful to
observe your country's applicable regulations.
The operating instructions must always be near the
machine. Put them in a plastic folder to protect them
from dirt and humidity. They must be read by every
operator before beginning work and observed con-
scientiously. Only persons who have been trained in
the use of the machine and have been informed of
the various dangers may work with the machine. The
required minimum age must be observed. In addition
to the safety requirements in these operating instruc-
tions and your country's applicable regulations, you
should observe the generally recognized technical
rules concerning the operation of identically con-
structed devices.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
2. Device description (Fig. 1-2)
1 Base plate
Pillar
2
Drilling table
3
Machine head
4
Keyless drill chuck
5
6 Grips
Drill chuck protection
7
8 Depth stop
Motor
9
10 On-Off switch
Belt protective hood
11
Locking grip for belt tension
12

3. Scope of delivery

Base plate (1)
Pillar (1)
Drilling table (1)
Machine head (1)
Keyless drill chuck(1)
Grips (3)
Chuck protection (1)
Fastening screws (3)
Allen key (hexagon socket screw key) 4mm (1)
Operating manual (1)
• Open the packaging and remove the device
carefully.
•
Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, store the packaging until the warran-
ty period has expired.
m Attention!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!

4. Intended use

This pillar drill is designed for drilling metal, plastic,
wood and similar materials. It is intended for use in
the private sector only.
Food and harmful materials may not be processed
with the equipment. The drill chuck is only designed
for use with drill bits and tools with a shaft diameter
of 1.5 to 13 mm, and for cylindrical tool shanks. The
equipment is intended for use by adults only.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not the
manufacturer will be liable for any damage or injuries
of any kind resulting from such misuse.
Please note that our equipment has not been desig-
ned for use in commercial, trade or industrial appli-
cations. Our warranty will be voided if the equipment
is used in commercial, trade or industrial businesses
or for equivalent purposes.
GB
19 / 44