Earthing Instructions; Service; Introduction; Using An Hvlp Spray System - Titan 0524044 Mode D'emploi

HAZARD: SKIN BURN INJURY
Heated parts can cause severe skin burn injury.
PREVENTION:
• Quick disconnect fittings on the hose and spray gun
become hot during use. Avoid skin contact with quick
disconnect fittings when they are hot. Allow quick
disconnect fittings to cool before disconnecting the
spray gun from the hose.

Earthing Instructions

Electric models must be earthed. In the event of an
electrical short circuit, earthing reduces the risk of electric
PE
shock by providing an escape wire for the electric current.
This product is equipped with a cord having an earthing
wire with an appropriate earthing plug. The plug must be
plugged into an outlet that is properly installed and earthed
in accordance with all local codes and ordinances.
DANGER — Improper installation of the earthing plug
can result in a risk of electric shock. If repair or
replacement of the cord or plug is necessary, do not
connect the green earthing wire to either blade
terminal. The wire with insulation having a green outer
surface with or without yellow stripes is the earthing
wire and must be connected to the earthing pin.
Check with a qualified electrician or serviceman if the earthing
instructions are not completely understood, or if you are in doubt as to
whether the product is properly earthed. Do not modify the plug provided.
If the plug will not fit the outlet, have the proper outlet installed by a
qualified electrician.
Caution – The power cord for this equipment acts as an
emergency stop/emergency switching off device. The
power cord must be placed near an easily accessible,
unobstructed socket-outlet.
Work or repairs at the electrical equipment:
These may only be carried out by a skilled electrician. No liability is
assumed for incorrect installation.
Power cord replacement must be performed by the manufacturer, its
service agent, or a similarly qualified person.
Operating Temperature
This equipment will operate correctly in its intended ambient, at a
minimum between +10°C and +40°C.
Relative Humidity
The equipment will operate correctly within an environment at 50% RH,
+40°C. Higher RH may be allowed at lower temperatures.
Measures shall be taken by the Purchaser to avoid the harmful effects of
occasional condensation.
Altitude
This equipment will operate correctly up to 3000 m above mean sea level.
Transportation and Storage
This equipment will withstand, or has been protected against,
transportation and storage temperatures of -25°C to +55°C and for short
periods up to +70°C.
It has been packaged to prevent damage from the effects of normal
humidity, vibration and shock.
i
A list of the materials used in the construction of the
equipment will be made available on request to validate
compatibility with the coating materials to be used.

Service

Should your spray system need service during the warranty period,
return your unit and the proof of purchase to the distributor where it was
purchased. At our option, the unit will be repaired or replaced. In a
continued commitment to improve quality, we reserve the right to make
component or design changes when necessary.
8500
GB

Introduction

This High Volume/Low Pressure (HVLP) spray system is
designed for applying coatings to surfaces that can be sprayed
faster than brushing or rolling and are too small for traditional
airless sprayers. Components of this system include a power
switch, a power cord, a filter warning light, a replaceable fuse, a
dual filtration system, a cup holder, an air hose, and an air outlet.
8
7
1 Air outlet
2 Cup holder
3 Filter (in the end of the
can)
4 Fuse
With this HVLP spray system, you can achieve the highest quality
professional finish possible with little or no preparation or setup
time. Please review all the information contained in this manual
before operating the system.

Using an HVLP Spray System

Refer to the following information to operate and understand your
HVLP spray system.

Setup

Use the following procedure to set up your HVLP spray system
for operation.
1. Plug the turbine power cord into a grounded, 3-slot
receptacle.
Keep the turbine at the maximum possible
distance from the spray area to safeguard
against explosion or fire that may be caused by
sparking electrical parts.
2. Prepare your spray gun for operation. Refer to your spray
gun manual for material preparation, setup, and spraying
information.
3. Attach the air hose to the air outlet on the turbine.
4. Attach the air hose to the air inlet on your spray gun.
5. Turn on the turbine and begin spraying.
7
1
2
6
5 Filter warning light
6 Power switch
7 Filter
8 Air hose
3
4
5