Cleanup; Special Cleanup Instructions For Use With Flammable Solvents; Overnight Storage; Long-Term Storage - Titan ED655 Mode D'emploi

Cleanup

6. Cleanup
The sprayer, hose, and gun should be cleaned
thoroughly after daily use. Failure to do so permits
material to build up, seriously affecting the
performance of the unit.
Attention
Always spray at minimum pressure with the gun
nozzle tip removed when using mineral spirits or
any other solvent to clean the sprayer, hose, or
gun. Static electricity buildup may result in a fire or
explosion in the presence of flammable vapors.
6.1 Special cleanup instructions for use with
flammable solvents
• Always flush spray gun preferably outside and at least one hose
length from spray pump.
• If collecting flushed solvents in a one gallon metal container,
place it into an empty five gallon container, then flush solvents.
• Area must be free of flammable vapors.
• Follow all cleanup instructions.
6.2

Overnight Storage

Shutdown
1. Turn the pressure control knob counterclockwise to the
minimum setting.
2. Turn the PRIME/SPRAY valve to PRIME to release system
pressure.
3. Trigger the gun to remove any pressure that may still be in the
hose.
4. Lock the trigger by rotating the trigger lock forward until it
stops.
5. Move the motor ON/OFF switch to OFF and unplug the
sprayer.
6. For latex materials only, pour 1/2 cup water slowly on the
top of the paint to prevent the paint from drying. For other
materials, seal the material container or paint hopper (with
the hopper cover) keeping the return tube in the material.
7. Wrap the spray gun assembly in a damp cloth and place it in a
plastic bag. Seal the bag shut.
8. Place the sprayer in a safe place out of the sun for short-term
storage.
All manuals and user guides at all-guides.com
GB
Startup
6.3
Attention

Clearing the Paint Hopper

Use the following procedure to clear the material out of the paint
hopper of a hopper unit.
8
1. Remove the gun from the plastic bag.
2. Stir the water into the paint for latex materials. Remove the
cover from the paint hopper or material container and stir the
paint for all other materials.
3. Check to be sure that the PRIME/SPRAY valve is set to PRIME
and that the pressure is completely reduced.
4. Plug sprayer in and Move the motor ON/OFF switch to ON.
5. After the sprayer is primed, turn the PRIME/SPRAY valve to
SPRAY and gradually turn the pressure control knob clockwise
to increase the pressure.
6. Test the sprayer on a practice piece and begin spraying.

Long-Term Storage

Do not allow material to build up on the motor or
the motor will overheat. Do not allow flammable
solvents to come in contact with the motor or they
could ignite.
you will need a bucket, cleaning solution, a
i
toothbrush, a wrench and cleaning rags.
Do not use mineral spirits or paint thinner on
latex paint, or the mixture will turn into a jelly-like
substance which is difficult to remove.
1. Lock the gun trigger by rotating the trigger lock forward until
it stops.
2. Turn the pressure control knob counterclockwise to the
minimum setting.
3. Turn the PRIME/SPRAY valve to PRIME.
4. Move the motor ON/OFF switch to OFF.
5. Direct the return tube into the original material container.
6. Move the motor ON/OFF switch to ON.
7. Turn the pressure control knob to 1/2 maximum pressure.
This will draw the remaining material in the paint hopper
through the pump, up the return tube, and into the material
container.
8. Turn the pressure control knob counterclockwise to the
minimum pressure setting.
9. Trigger the gun to relieve pressure and lock the gun.
10. Remove the spray tip and guard and place them into a
container of water or appropriate solvent for the type of
material with which you are painting.
11. Fill the paint hopper with water or an appropriate solvent for
the type of material with which you are painting.
12. Direct the return tube into a waste bucket.
ED655