Final Cleanup - Titan ED655 Mode D'emploi

13. Increase the pressure to 1/2 the maximum pressure. Let the
water or solvent circulate for 2-3 minutes to flush material out
of the pump, the paint hopper, and the return tube.
Clearing the Paint Hose
1. To save material left in the hose, release the gun trigger lock
and carefully trigger the gun with the spray tip removed
against the inside of the material container.
2. Turn the pressure control knob counterclockwise to the
minimum pressure setting.
3. Turn the PRIME/SPRAY valve to SPRAY.
4. Turn the pressure control knob slowly until material starts to
flow into the bucket. As soon as the water or solvent starts to
come into the bucket, release the trigger.
5. Change to clean water or solvent, point the gun to the side
of the waste bucket, and continue circulating for another 5
minutes to thoroughly clean the hose, pump and spray gun.
6. Turn the pressure control knob counterclockwise to its lowest
setting.
7. Turn the PRIME/SPRAY valve to PRIME.
8. Trigger the gun to remove any pressure which may still be in
the hose.
9. Lock the gun trigger by rotating the trigger lock forward until
it stops.
10. Move the motor ON/OFF switch to OFF.
11. Cover the material container and set it aside.
Clearing the Gun
1. Remove the spray gun from the paint hose using two
adjustable wrenches.
2. Remove the filter housing from the gun. Place the gun and
the filter assembly into a container of water or solvent to soak.
3. Clean the spray tip and gun filter with a soft brush.
4. Reassemble the gun and filter. Assemble the spray tip in the
cleaning position with the arrow pointing to the back of the
gun.
5. Attach the paint hose to the gun and tighten using two
wrenches.
6. Move the motor ON/OFF switch to ON.
7. Unlock gun trigger by turning the gun trigger lock so that it is
parallel to the gun handle.
8. Turn the PRIME/SPRAY valve to SPRAY and point the gun to
the side of the waste bucket.
9 Trigger the gun and gradually turn the pressure control knob
clockwise to 1/2 pressure. Continue to trigger the gun for
approximately 30 seconds.
10. Turn the pressure control knob counterclockwise to its lowest
setting.
11. Turn the PRIME/SPRAY valve to PRIME.
12. Trigger the gun to remove any pressure which may still be in
the hose.
13. Lock the gun trigger by rotating the trigger lock forward until
it stops.
14. Move the motor ON/OFF switch to OFF.
ED655
All manuals and user guides at all-guides.com
GB

Final Cleanup

12. Turn the PRIME/SPRAY valve to SPRAY to distribute the oil.
14. Turn the PRIME/SPRAY valve to PRIME.
17. Move the motor ON/OFF switch to OFF.
9
1. Remove the tip assembly.
2. Move the motor to ON.
3. Turn the PRIME/SPRAY valve to SPRAY.
4. Turn the pressure control knob clockwise to 1/2 power.
5. Trigger the gun into the cleaning bucket until the hopper or
solvent bucket is empty.
6. Refill the hopper or solvent bucket and continue flushing
the system until the solution coming out of the gun appears
clean.
7. Lock the gun and turn the pressure control knob
counterclockwise to its lowest setting.
8. Turn the PRIME/SPRAY valve to PRIME.
9. Remove the hopper or suction set from the inlet valve.
10. Clean the threads of the inlet valve with a damp cloth.
11. Fill the inlet valve with a light household oil.
Proper cleaning and oiling of the pump after use
i
are the most important steps you can take to insure
proper operation after storage.
13. Turn the pressure control knob counterclockwise to its lowest
setting.
15. Trigger the gun to remove any pressure that may still be in the
hose.
16. Lock the gun trigger by rotating the trigger lock forward until
it stops.
18. Remove the hopper filter and clean in clean water or the
appropriate solvent. Use a soft brush.
19. Return the hopper filter to its position in the hopper.
20. Replace the hopper or suction set on the inlet valve.
21. Wipe the entire unit, hose, and gun with a damp cloth to
remove accumulated material.
Cleanup