Overview Menu Options - Wilo Sinum MP M-2-50 Notice De Montage Et De Mise En Service

English

7.3. Overview menu options

Change menu
Date, time
Example:
Summer time is ON
date: 23.10.2010.
Time:
18.00 hours,
12 minutes, 57 seconds.
Line below:
Functional assignment for
sensor buttons.
Main menu
Degassing
procedure
ON, OFF
Gas sensor, sensor
connection array
required (optional)
(Test cycle ON,
see 8-5 -2)
Distribution of
sleep intervals to
weekdays (next
page)
22
Turkish
4-20
Save configuration
(....)
on SD
2-2-1 (....)
German
SD-kaart
2-2 4-1
Data transfer
Date/ Time Language
menu menu menu
2 3 4
Error Sensors
Degassing message valves
8-5 8-4 8-3
Minimum
Activated Pressure pressure limiter
8-5-1 8-4-1 8-3-1
Controlled (....)
8-5-2 (....)
Phase
Standby monitor
8-5-3 8-4-17
Operating
Normal pressure menu
8-5-4
Fast
Example:
8-5-5
P ; Trigger pressure safety valve 6 bar (appendix)
Closing
SV
(From order specification <= nominal pressure unit)
times
P ; final pressure 5.4 bar
E
Safety valve, code letter DGH
P x 0.9 [P >= 3 bar]; P
SV SV SV
Safety valve, code letter H
8-5-6
P - 0.5 bar [P = 3 bar]
SV SV
(From order specification)
P ; Operating pressure 1.2 bar (configurable range by unit type)
A
P ; Upper operating pressure tolerance 0.2 bar (default)
A+
P ; Lower operating pressure tolerance 0.2 bar (default)
A-
(From order specification)
P ; Positive pressure 0.3 bar (default, recommended)
+
P ; Displayed value, message: P
0
(e.g.: = P + P + P
static steam dynamic = 0.7 bar
Start
9-10
Pressure
ID Vat settings
9-9
Operational
Example:
calibration
The nominal volume
(see section 5.2) is
shown on the vessel
label or SPC ID sticker.
This corresponds to the
9-6
vessel capacity with the
letter A or B. ID Vat
For example:
A-200
B-200
9-5
"
Read
manual
9-1
Configuration Start
Loginmenu menu menu
5 8 9
Level Pressure
8-2 8-1
Operating
Top-up pressure
vessel calibration
8-2-1 8-1-1
Drain
software, hardware
8-2-2
commissioning,
vessel calibration
See: Maintaining
Error history, no longer active
errors, error no., date, time
- 0.3 bar [P < 3 bar]
SV
- P - P = 1.2 - 0.2 - 0.3 = 0.7 bar
A A- +
)
Werkingsindicator
Actual pressure 1.4 bar
Duopump unit; pumps, valves not ON.
Vessel content 0 %, error min. priming
water ON (error no.: 19; 10).
top-up valve 230v, self-monitoring, ON;
No impulse water meter, top-up time < 1 minute.
Gas sensor enabled, degasification mode normal
(Degassing not ON due to min. priming water).
SPC terminal
Operating Service
Menu menu
10 11
Order number
Manufacturer,
supplier
(traceability) Main switch on;
SPC terminal with
11-1
main menu on;
Unit
information Fields and messages
with backlighting
Unit, vessel,
are active.
(test)
- Menu 2: Module exten-
sion option required;
11-2
- Menu 3: Check, change
Version
information
date, time
Control unit, - Menu 4: Check, change
language
(traceability)
- Menu 5: Not
11-3 possible, not necessary;
- Menu 8: Defaults
Start
can be still changed
Date: Start of
after start or as required:
- Menu 8-1-1: Applica-
tion to change P
(statistics)
11-4
- Menu 8-2-2: Can be
switched off/on if
Maintaining
drainage exists;
- Menu: 8-3-1: Install
on request, then
enable;
11-5
- Menu 8-4-1...17:
Group error message
Error list
assignments; enable/
disable on request;
- Menu 9:
(analysis)
- Menu 9-1: Please note;
11-6
- M enu 9-5: Input, select
nominal capacity;
Operating hours
- Menu 9-6: Execute;
- Menu 9-7: Execute;
(Statistics)
- M enu 9-8: Check,
change;
11-7
- M enu 9-9: Operating
Top-up,
range determined,
overflow spill
execute.
Quantities,
times
(statistics)
11-8
Example:
, P
e A
Fig. FM.038.V02.15
WILO SE 08/2018