Type Key Pump Control Unit; Type Key Controller Unit - Wilo Sinum MP M-2-50 Notice De Montage Et De Mise En Service

Alphabetic glossary of abbreviations in terminal plan.
Note: mentioned switch settings are in current-free, un-switched situation.
accessory (SPC Extension volume, pressure analog, optional)
COM COM interface; serial port
COM The common port
data (Data protocol, optional)
drs (Diaphragm rupture sensor, optional)
extra low voltage Protective low voltage
fault Error message, common error message Displayed switch setting is error.
F1/2 MS1/2 (Motor circuit-switch 1/2; Motor circuit-switch combination 1/2, SPCx-hw)
gs (Gas sensor, optional Gas sensor flexible connection assembly)
high voltage Voltage as per markings on the automat
mains supply Power feed
mpl (Minimum pressure limiter, optional)
M3/3.1 V3/3.1 Motor 3 (top-up, optional) / 3.1 (drainage, optional); valve 3 (top-up) / 3.1
(drainage, optional)
M1 V4 K1/MS1 Motor 2 (pressure increase); valve 5 (not applicable); switch 2 / motor circuit-switch combination 2, SPCx-hw
M2 V5 K2/MS2 Motor 2 (pressure increase); valve 5 (not applicable); switch 2 / motor circuit-switch combination 2, SPCx-hw
niveau Level, content
ohmic load Ohmic load, resistance
option (not applicable)
pressure Pressure
pwm (Impulse water meter, optional)
ps (Pressure switch; level switch min. level, top-up pump, optional)
refill / drain Top-up / (drain , optional)
sensors Sensors
tc (Temperature switch, optional)
V1; 1.1 Valve 1; 1.1; parallel, air release valve (pressure drop)
V2 Valve 2; air release valve (pressure drop)
V2.1 Valve 2.1 (not applicable)
5.3. Type key Pump control unit
E.g.: DP80 - 1 - 50
Key: AB - C - D
Nom. frequency of the operating voltage (Hz): 50 = 50 Hz; 60 = 60 Hz
Pump manufacturer:
Performance class:
Module version:
5.4. Type key Controller unit
- lw
E.g.: SPC 1.2
SPC 1.2 - hw - 1 - 1 - 7 - 1 - 0
Key: SPC x - y - A - B - C - D - E
Hardware version
Output range:
lw = low output
MP; DP / P ≤ 2.2 kW
N
hw = high output
MP / P ≤ 4,0 kW;
N
DP / P ≤ 8,0 kW
N
Installation and operating instructions Wilo-Sinum
1; 2; 3; 4; 5
M; 1; 2; 10; 20; 60; 80; 90; 100; 130
MP = Monopump; DP = Duopump
Phase monitoring/SPC-extension module, Ananlogue signalling: 0 = Not present;
Start type: 1 = Direct start; 2 = Soft start
Nominal current range: 1 = 1.1 - 1.6; 2 = 1.4 - 2.0; 3 = 1.8 - 2.5; 4 = 2.2 - 3.2;
5 = 2.8 - 4.0; 6 = 3.5 - 5.5; 7 = 4.5 - 6.3; 8 = 5.5 - 8.0;
9 = 7.0 - 10.0; 20 = 1.0 - 1.6; 21 = 1.6 - 2.5; 22 = 2.5 - 4.0;
23 = 4.0 - 6.3; 24 = 6.3 - 10.0; 25 = 8.0 - 12.0
1 = 1 motor; 2 = 2 motors
Number of motors:
Voltage: 1 = 400 V ± 10 % / 3 N PE / 50/60 Hz
English
Fig. FM.015.V01.15
1 = Present
Fig. FM.016.V01.15
11