Unlocking An Nfc Upgrade Or Credit Card; Special Programme Upgrade; User Level; Access Level Startup - LORCH ControlPro Manuel D'utilisation

Unlocking an NFC upgrade or credit card

 Hold the NFC card to the NFC read area A43.
9 The code "Un Loc" is displayed in the 7-segment displays
A4 and A12.
‰ The operation can be cancelled by pressing the crater fill-
ing button A2.
 Press the gas test button A14 to confirm unlocking.
9 The card is unblocked, but the credit is erased.
Alternatively, you can send the blocked card to
i i
the Lorch service department, in order to have
it checked.
12.3

Special programme upgrade

 Hold the NFC card to the NFC read area A43.
9 The NFC card is completely read in when the code "oK" ap-
pears in the right-hand A12 7-segment display.
 Remove the NFC card from the NFC read area A43.
9 The code "SPr" appears in the left-hand 7-segment display
A4.
9 The special program location "c 1" is displayed in the right-
hand 7-segment display A 12.
 Select the desired special program location "c 1 to c 7" us-
ing the rotary button A44.
Take account of already occupied special pro-
i i
gramme locations.
– Flashing special programme locations are
occupied,
– Continuously lit special programme loca-
tions are free.
 Confirm the safety prompt in the graphic display A52.
If an occupied special programme location is
i i
selected, this will be over-written without any
further notice.
12.4

User level

This function allows user rights to be enabled on various lev-
els.
The switch-on user level Con 8 is set by default. This means
that all the welding functions are available when the device
is switched on.
This switch-on user level can be changed, e.g. to Con 0 (theft
protection). This means that the device is blocked after switch-
on. The user must then log in with their personal user card.
 Hold the user card on the NFC read surface A43 until the
code nFc appears in the left-hand 7-segment display A4
and the code oK appears in the right-hand 7-segment dis-
play.
- 44 -
CUL Name/function
0 Locked (Theft protection)
1 Robot control / Read only
(Robot control parameter set-
ting/for info only on user inter-
face.)
2 WPS Welder Basic
3 WPS Welder Advanced
(WPS Welder Advanced)
4 Welder Basic
(Welder Basic)
8 Welder Advanced
(Welder Supervision)
10 Administrator
Tab. 2: User level
12.5

Access level startup

This function allows user rights to be enabled on various lev-
els.
The factory setting is the Access level startup welding super-
visor (Level 8). This means that all the welding functions are
available when the device is switched on.
This access level Startup can be changed, e. g. to 0 (theft pro-
tection). This means that the device is blocked after switch-on.
The user must then log in with their personal user card.
The access level Startup can only be changed
i i
above Authorization level Administrator (Level
10)!
 Hold the user card Administrator (Level 10) on the NFC
read surface A43 until the code nFc appears in the left-
hand 7-segment display A4 and the code oK appears in
the right-hand 7-segment display.
9 The LED Welder A3 and the LED Admin A3b light up.
 Press the Menu A50 button.
9 The main menu is displayed in the graphic display A52.
 Select the menu point "Customer settings" by rotating the
operating button A49.
 Confirm the menu point by pressing the operating button
A49.
9 The customer settings sub-menu M6-1 is displayed in the
graphic display A52.
 Select the menu point "Access level startup" by rotating
the operating button A49.
 Confirm the menu point by pressing the operating button
A49.
9 The Access level startup sub-menu M6-1-0 is displayed in
the graphic display A52.
909.3059.9-03
NFC Functions
- - - -
X - - -
X - 10% -
X - 10% X
X X X -
X X X X
X X X X
02.20