Unlocking An Nfc Upgrade Or Credit Card; Special Programme Upgrade; User Level; User Management - LORCH BasicPlus Manuel D'utilisation

12.3 Unlocking an NFC upgrade or credit
card
 Hold the NFC card against the NFC read area A43.
9 The code "Un Loc" is displayed in the 7-segment displays
A4 and A12.
‰ The operation can be cancelled by pressing the Exit but-
ton A2.
 Press the Save button A14 to confirm unlocking.
9 The card is unlocked and cancelled for the incorrect instal-
lation.
Alternatively, you can send the blocked card to
i i
the Lorch service department, in order to have
it checked.
12.4

Special programme upgrade

 Hold the NFC card against the NFC read area A43.
9 The NFC card is completely read in when the code "oK" ap-
pears in the right-hand A12 7-segment display.
 Remove the NFC card from the NFC read area A43.
9 The code "SPr" appears in the left-hand 7-segment display
A4.
9 The special programme location "c 1" is displayed in the
right-hand 7-segment display A12.
 Select the desired special programme location "c 1" to "c 7"
using the rotary button A44.
Take account of already occupied special pro-
i i
gramme locations.
– Flashing special programme locations are
occupied,
– Continuously lit special programme loca-
tions are free.
 Confirm the upgrade with the Save button A14.
If an occupied special programme location is
i i
selected, this will be over-written without no-
tice.
12.5

User level

This function allows user rights to be enabled on various lev-
els.
The switch-on user level Con 8 is set by default. This means
that all the welding functions are available when the device
is switched on.
This switch-on user level can be changed, e.g. to Con 0 (theft
protection). This means that the device is blocked after switch-
on. The user must then log in with their personal user card.
 Hold the user card on the NFC read surface A43 until the
code nFc appears in the left-hand 7-segment display A4
and the code oK appears in the right-hand 7-segment dis-
play.
- 30 -
CUL Name/function
0 Locked (Theft protection)
1 Robot control/Read only
(Robot control parameter
setting/for info only on user
interface.)
2 WPS Welder Basic
3 WPS Welder Advanced
(WPS Welder Advanced)
4 Welder Basic
(Welder Basic)
8 Welder Advanced
(Welder Supervision)
10 Administrator
Tab. 7: User level
12.6

User management

The function is shown using the example of Welding Supervi-
sor and WPS Basic users.
Welding Supervisor log-in:
 Hold the Welding Supervisor NFC card (user level 8) against
the NFC read surface A43 for at least 3 sec.
9 The code nFc appears in the left-hand 7-segment display
A4. After approx. 3 sec., the code oK appears in the right-
hand 7-segment display as log-in confirmation.
 Set the desired material/wire/gas combination, welding
process, main and secondary parameters. (These setting
values are applied for the WPS Basic user)
WPS Basic user log-in:
 Hold the WPS Basic NFC card (user level 2) against the NFC
read surface A43 for at least 3 sec.
9 The code nFc appears in the left-hand 7-segment display
A4. After approx. 3 sec., the code oK appears in the right-
hand 7-segment display as log-in confirmation.
‰ The values set by the welding supervisor (material/wire/
gas combination, welding process and secondary param-
eters) cannot be changed. The arc dynamics can only be
changed by 30 % and the main parameters by 10 %.
Should these restrictions still exist for the WPS
i i
Basic user after switching the device off and on,
then the switch-on Con user level must be set
to 2
909.3049.9-03
NFC Functions
- - - -
X - - -
X - 10% -
X - 10% X
X X X -
X X X X
X X X X
02.20