Storage - Scheppach MTC42-5P Traduction Des Instructions D'origine

Oiling the gears, hedge trimmer
Oil the gears every 10 to 20 operating hours.
1 Position the grease gun at the lubricating nipples
Fig. 41 (P).
2 Insert some grease.
Attention! Fill only a small amount of grease. Do not
overfill.
Oil the cutting tools and the angle adjustment with
environmentally friendly lubricant.
Adjusting the idle speed Fig. 50
If the cutting device runs idle, correct the idle speed.
1. Allow the engine to warm for 3-5 minutes
(No high speeds!).
2. Turn the adjusting screw (S):
clockwise
­ idle speed increases (+)
counterclockwise
- Idling speed decreases (-)
The idle speed is 3000 min
-1
Contact the manufacturer if the cutter continues
to run at idle.
Do not continue to operate the unit!
The user is responsible for all damages caused
by non-compliance with instructions in this
manual.
This also applies to non-authorized modifica-
tions of the tool, use of non-authorized spare
parts, accessories, working tools, unrelated and
not intended use, secondary damages due to
use of faulty components.
Wear Parts
Even when used in the intended way, some compo-
nents are subject to normal wear. They have to be
replaced depending on the kind of duration of usage.
These parts include, among others, the cutting tool
and the retaining disk.
m Warning! Use only original manufacturer's re-
placement parts, accessories and attachments. Fail-
ure to do so can cause poor performance, possible
injury and may void your warranty
Important hint in case of sending the equipment
to a service station:
Due to security reasons please see to it that the
equipment is sent back free of oil and gas!
Ordering replacement parts
Please quote the following data when ordering re-
placement parts:
• Type of machine
• Article number of the machine
Replacement parts / accesories:
For the cutting equipment listed here, you can always
use the safety guards provided with the unit.
44 GB
Grass trimmer/brush cutter:
Spool with Ø 450
Spool TRICORD Ø450
Spare spool TRICORD
Blade with 3 teeth Ø 255 x 1.4
Transport guard for blade 3 teeth
Blade with 4 teeth Ø 255 x 1.5
Transport guard for blade 4 teeth
Blade with 8 teeth Ø 255 x 1.5
Transport guard for blade 8 teeth
Safety shield for grass trimmer
Pole pruner:
Saw chain Oregon 91PJ040X
Guide rail Oregon 100SDEA318
Transport guard for chain
Extension for pole pruner
Hedge trimmer:
Blade for hedge trimmer 400 mm
Transport guard for blade

11. Storage

Cleaning
• Keep handles free of oil, so you always have a secure
hold.
• Clean the equipment as required with a damp cloth and,
if necessary, mild washing up liquid.
m Important!
• Always pull out the spark boot plug each time before car-
rying out any cleaning.
• Never immerse the equipment in water or other liquids in
order to clean it.
• Store the petrol multi garden tool in a safe and dry place
out of the reach of children.
Storage
Important: Never put the equipment into storage for longer
than 30 days without carrying out the following steps.
Storing the equipment
If you intend to store the equipment for longer than 30 days,
the equipment must be prepared accordingly. Otherwise
the fuel still remaining in the carburetor will evaporate and
leave a rubbery sediment. This can cause problems when
starting up the equipment and may require expensive re-
pairs.
1 Slowly remove the fuel tank cap to release any pres-
sure that may have formed in the tank. Carefully empty
the tank.
2 To remove the fuel from the carburetor, start the engine
and let it run until the equipment stops.
3 Leave the engine to cool (approx. 5 minutes).
4 Remove the spark plug (see section 10 Change and
clean the spark plug).
5 Add one teaspoon of 2-stroke engine oil into the com-
bustion chamber. Slowly pull the starter cord several
times to apply a layer of oil to all internal components.
Fit the spark plug again.
7910700706
7910702702
7910702704
7910700702
3904801065
7910700705
3904801066
7910700711
3904801066
3904803034
7910700704
3904801037
3904801039
7910700710
7910700703
3904801043