Transport; Cleaning And Maintenance; Cleaning Work - Parkside Pbv 4200 A1 Instructions De Fonctionnement Et De Sécurité

12. Transport

m WARNING!
Risk of injury!
Unintended and unexpected start-up of the product may lead
to injuries.
- After loading, switch off the engine and, after the engine
has cooled down, remove the spark plug connector from
the spark plug.
- The product can cause severe crushing injuries due to its
own weight.
Allow the engine to cool down before transporting or loading
to avoid burns and to prevent fire hazards.
m The machine can fall and cause damage or injury if it is not
lifted properly.
When transporting over longer distances, drain the fuel tank
completely.
Secure the machine on the transport vehicle against rolling,
slipping or tipping over and also lash down the device.

13. Cleaning and maintenance

m WARNING!
Danger of injury and burning!
The product can start unexpectedly and cause injuries. In ad-
dition, temperatures of 80° C and more can be reached.
- Switch off the motor before carrying out any cleaning or
maintenance work.
- Allow the engine to cool down.
- Disconnect the spark plug connector from the spark plug.
m WARNING!
Risk to health!
Inhaling petrol/lubricant vapours may lead to severe health
damage, loss of consciousness and, in extreme cases, to death.
- Do not inhale petrol/lubricant vapours.
- Only use the product outdoors.
NOTE!
Risk of damage!
Water entering the housing can cause engine damages. In
addition, the jet of a high-pressure cleaner can damage parts
of the product.
- Clean the product with a cloth, a hand brush, etc.
- Do not immerse the product in water or any other liquid
and do not wash it with a high-pressure cleaner.
Maintenance plan
After 10 After 25
operating operating
hours hours
Air filter Clean Clean
Spark
Check Clean
plug
V-belt
Engine
Check Replace
oil level
Every Every Every
50 op- 100 300
erating operating operating
hours hours hours
Clean Clean Replace
Clean Clean Replace
Check Replace
Replace

13.1 Cleaning work:

m WARNING!
Risk of injury!
Unintended and unexpected start-up of the product may lead
to injuries.
- Switch off the engine before carrying out any cleaning or
maintenance work and after the engine has cooled down,
disconnect the spark plug connector from the spark plug.
Maintaining your petrol scarifier ensures a long service life for
the machine and its components.
• Check the general condition of the petrol scarifier and
check for loose screws, misalignment and jamming of mov-
ing parts, broken or worn parts and other issues that could
impair function of the machine.
• Use a high quality light machine oil to lubricate the moving
parts.
• Clean the underside of the petrol scarifier as soon as grass
cuttings stick to it. The machine will not work well if the
underside is not clean.
• Re-attach the spark plug connector after cleaning and
maintenance work.
13.2 Checking and replacing the V-belts
Never use the device without the belt cover (7). If the belt
cover (7) is not in place, it is possible that your hand will be
caught causing you serious injury.
13.2.1 Tensioning the V-belt (Fig. 11 + 5)
The V-belt (7a) must be in good condition to ensure optimum
power transmission from the engine to the cutting roller. Check
the condition of the V-belt (7a).
1. Switch the engine off and let it cool down.
2. Remove the belt cover (7) to gain access to the V-belt
(7a). To do this, use an open-end spanner size 8 (alter-
natively a socket spanner) (not included in the scope of
delivery) to loosen the 4 hexagonal bolts on the belt
cover (7).
3. Now check the belt tension (thumb pressure). If the V-belt
(7a) gives more than 10-15 mm (thumb pressure), you
must retighten it.
4. Disengage the catch basket (16) (Fig. 5).
5. Loosen the top nut on the stud bolt (7c) with an open-end-
ed spanner size 14 (not included in the scope of delivery)
and screw them up to the upper end of the stud bolt.
6. Now retention the V-belt (7a) by turning the bottom nut on
the stud bolt (7b) upwards using an open-ended spanner
size 14 (not included in scope of delivery).
7. Recheck the belt tension (thumb pressure). If the V-belt
(7a) gives more than 10-15 mm (thumb pressure), you
must retighten it again.
8. Fit the belt cover (7) back on. And tighten the 4 hexagonal
bolts on the belt cover (7) with an open-ended spanner
size 8 (alternatively a socket spanner) (not included in the
scope of delivery).
9. Engage the catch basket (16) again.
GB/IE/NI/CY/MT 11