Setting The Microwave To Combined Operation; Drying The Cooking Compartment - CONSTRUCTA CC4W91860 Notice D'utilisation

Microwave
en
Changing the cooking time
Touch 0 until the + symbol is highlighted.
1.
Use the settings area to change the cooking time.
2.
After a few seconds, the change is applied.
Changing the microwave power output
Touch !.
1.
Select the required power level using the settings
2.
area.
Pausing the operation
Touch the IH field or open the appliance door.
1.
The operation is suspended and the IH LED flashes.
Close the appliance door.
2.
Touch the IH field.
3.
The operation is continued and the IH LED lights up.
Cancelling operation
Touch #.
The appliance will stop heating and all the settings will
be cleared.
Note: The fan may continue to run after the appliance
has been paused or stopped.
Setting the microwave to combined
operation
Y ou can combine the microwave function with all types
S e t t i n g t h e m i c r o w a v e t o c o m b i n e d o p e r a t i o n
of heating. The appliance heats up and the microwave
is switched on at the same time. As a result, the food is
ready in a much shorter time.
Combination options
~ Hot air
■
# Hot air grill
■
3 Pizza setting
■
$ Grill
■
Exceptions:
! Microwave setting 900 W
~ Hot air 40 °C
Setting the combination mode
Example: Hot air ~ 190 ºC with microwave at 360 W,
17 minutes.
Touch !.
1.
The appliance is ready to use. The maximum
microwave power output of 900 W will be displayed
as the default value on the display. You can change
this at any time.
Set to 360 W using the settings area.
2.
The microwave power output and a default cooking
time will be shown on the display.
Touch !.
3.
Use the settings area to set the Hot air ~ type of
4.
heating.
A default value for the temperature is shown on the
display.
Touch °C/A
5.
Set the temperature to 190 ºC using the settings
6.
area.
Touch 0.
7.
48
Set the required cooking time of 17 minutes using
8.
the settings area.
Touch IH.
9.
The operation starts and the IH LED lights up. The
cooking time starts counting down.
The cooking time has elapsed
A signal sounds and the IH symbol stops lighting up.
Combination mode has finished. Touch any field to end
the acoustic signal.
Changing the microwave power output
Touch !.
1.
Select the required power level using the settings
2.
area.
Pausing the operation
Touch the IH field or open the appliance door.
1.
The operation is suspended and the IH LED flashes.
Close the appliance door.
2.
Touch the IH field.
3.
The operation is continued and the IH LED lights up.
Cancelling operation
Touch #.
The appliance will stop heating and all the settings will
be cleared.
Note: The fan may continue to run after the appliance
has been paused or stopped.

Drying the cooking compartment

Dry the cooking compartment after operation to ensure
that no moisture remains.
Heating up the cooking compartment
To dry, heat up the cooking compartment so that the
moisture in the cooking compartment evaporates. Then
open the appliance door to allow the steam to escape
from the cooking compartment.
Allow the appliance to cool down.
1.
Remove the worst dirt from the cooking compartment
2.
immediately and wipe away moisture from the
cooking compartment floor.
If necessary, press # to switch on the appliance.
3.
Touch !.
4.
The different types of heating are displayed.
Use the settings area to select Hot air grill #.
5.
Touch °C/A and use the settings area to set the
6.
temperature to 150 °C.
Touch 0 twice.
7.
The cooking time symbol + is highlighted in the
display.
Use the settings area to set a cooking time of 15
8.
minutes.
Press IH to start the operation.
9.
The drying function starts and ends automatically
after 15 minutes.
Drying the cooking compartment by hand
Allow the appliance to cool down.
1.
Remove any food remnants from the walls of the
2.
cooking compartment.
Dry the cooking compartment with a sponge.
3.
Leave the appliance door open for 1 hour so that the
4.
cooking compartment dries completely.