EUFAB BIKE FOUR Manuel De L'opérateur page 8

BIKE FOUR for trailer tow bar rack for up to four bicycles
OVERVIEW
1. PROPER USE OF THE PRODUCT
2. SCOPE OF DELIVERY
3. SPECIFICATIONS
3.1 TOW BAR REQUIREMENTS
4. SAFETY NOTES AND IMPORTANT INFORMATION
5. OPERATING INSTRUCTIONS
5.1 MOUNTING THE RACK TABLE
5.2 MOUNTING THE U-SHAPED BAR
5.3 INSTALLATION OF THE REAR LIGHTS
5.4 LAYING ELECTRICAL CABLES
5.5 MOUNTING THE LICENSE PLATE HOLDER
5.6 MOUNTING THE FRAME HOLDER
5.7 MOUNTING THE BICYCLE RACK ON THE TRAILER TOW BAR
5.8 MOUNTING THE BICYCLES TO THE CARRIER
5.9 USING THE TENSION-RELIEF STRAP
6. MAINTENANCE
7. NOTES REGARDING ENVIRONMENTAL PROTECTION
8. CONTACT INFORMATION
WARNING
Please read the operating instructions carefully prior to use and observe all safety instructions!
Store the original packaging, the receipt and these instructions so that they may be consulted at a later date! When passing on
the rack, please include these operating instructions as well.
Non-compliance can lead to personal injuries, damage to the device or your property!
Please check the contents of package for integrity and completeness prior to use!
1. PROPER USE OF THE PRODUCT
The BIKE FOUR bicycle rack is mounted to the trailer tow bar of a car and is designed for the transportation of up to four bicycles.
Intended use also includes the observation of all information provided in these operating instructions, particularly the observance of safety instructions. Any
other utilisation is considered to be contrary to the intended purpose and may lead to material damages or personal injuries. EAL GmbH assumes no liability for
damage resulting from improper use.
2. SCOPE OF DELIVERY
1 x Rack table, left
1 x Rack table, right
1 x Table traverse
1 x Base
2 x Connection plate
1 x U-shaped bar
2 x Protective rubber
2 x Stabilisation plate
1 x License plate holder
3. SPECIFICATIONS
Weight 20 kg
Maximum payload 30 kg (with a permitted supporting load of 50 kg)
40 kg (with a permitted supporting load of 60 kg)
55 kg (with a permitted supporting load of 75 kg)
70 kg (with a permitted supporting load of 90 kg)
Maximum of 70 kg (with a permitted supporting load of 100 kg)
3.1 TOW BAR REQUIREMENTS
• The trailer tow bar must be approved in its construction.
• Ball and ball rod must have been forged in one piece.
• Only mount the bicycle rack to a tow bar of steel St52-3, grey cast iron GGG52 or higher quality.
• The D-value of the tow bar ball must be at least 7.6 kN
• Never mount the rack to a tow bar made of aluminium, other light metals or plastic
8
1 x Protective mould, left
1 x Protective mould, right
1 x Light set
8 x Wheel stopper
16 x Tensioning strap, short
1 x Frame holder, short
1 x Frame holder, long
1 x Frame holder, wheel to wheel
1 x Installation wrench
1 x Handle screw, lockable
4 x Headless hexagonal screw M8 x 55
2 x Hexagonal screw M8 x 50
6 x Nut M8
8 x Washer 15.8 x 8.5 x 1.1
4 x Spring washer 13 x 8.5 x 2.2
4 x Lock screw M6 x 70
2x Lock screw M6 x 60
2 x Lock screw M6 x 45
2 x Lock screw M6 x 30
6 x Nut M6
10 x Washer 17.9 x 6.5 x 1.2
4 x Nut M5
4 x Washer 13.6 x 5.5 x 1
4 x Knob nut M6
2 x Plastic plug 80 x 30
1 x Tensioning strap, long
1 x Tension-relief strap, two-piece
1 x Hook
Cable tie
8
8
8
8
9
10
10
11
11
11
11
12
12
12
13
13
13
13