Titan Maxum II Notice D'utilisation page 6

Air Flow
Valve Nut
Material
Adjustment
Housing
Seal and
Spring
Needle
8. Insert an 1/8 inch hex wrench into the back of the needle
guide shaft.
9. Hold the retaining nut with a wrench and turn the 1/8 inch
hex wrench counterclockwise to remove the retaining nut.
10. Pull the needle guide shaft out of the gun body.
Retaining Nut
Needle
Guide Shaft
Replacing the Air Valve Seals
1. Remove the old rear air valve seal. It may stay on the end
of the needle guide shaft spring or in the material flow
adjustment housing.
2. Slide the new rear seal into the material adjustment housing.
3. Remove the front seal retaining clip using a snap-ring pliers.
4. Slide the old front air valve seal off of the needle guide shaft.
5. Place the new front air valve seal on the needle guide shaft
with the beveled side facing the gun.
NOTE: Make sure that the new front air valve seal looks like
the one that was just removed.
SIDE VIEW
Front Air Valve Seal
6. Snap the front seal retaining clip onto the needle guide shaft.
Front Seal Retaining Clip
Front Air
Valve Seal
Needle
Guide Shaft
Spring
Rear Air
Valve Seal
Material Flow Adjustment Housing
Removing the Packing
1. Remove the packing nut using a 3⁄8 inch wrench.
2. Insert a long, narrow-bladed flathead screwdriver through the
back of the gun and into the packing hole.
3. Press the screwdriver firmly into the packing and turn
counterclockwise. This should back the old packing out of the
threaded hole. If it does not, push the screwdriver more firmly
English
Packing Nut
NOTE: Make sure all of the old packing is removed before
Installing the New Packing and Reassembling the Gun
1. Place the new packing into the packing hole.
2. Thread the packing nut one turn into the packing hole. Do
3. Push the needle guide shaft through the back of the gun body
4. Grasp the material flow adjustment housing with the needle
5. Tighten the packing nut securely using a 3/8 inch wrench,
6. Thread the air flow valve nut and air flow adjustment knob
7. Assemble the trigger by inserting the retaining pin or pins and
8. Pull the trigger to make certain the needle moves freely. If
Replacing the Check Valve, Valve Seal, and Air Tubes
The check valve is a one-way valve designed to allow air into the
cup, pressurizing the cup's contents. Because it is a one-way valve, it
prevents paint from seeping up the air tube into the air passages of
the gun. It also eliminates any delay in material flow when the gun is
triggered by maintaining pressure in the cup.
The check valve rotates open easily for cleaning. It contains a valve
seal that can be removed and cleaned with soap and water for
waterborne materials or a compatible solvent for other materials. To
Beveled Side
replace the check valve, the valve seal, and/or the air tubes:
1. Pull the lower air tube from the bottom of the check valve.
2. Pull the check valve from the upper air tube.
3. Unscrew the two halves of the check valve.
4. Remove the worn valve seal.
5. Clean the check valve body with a solvent appropriate to the
NOTE: Thoroughly clean the inside of the top half of the
6. Insert a new valve seal, stem up, into the top of the check
7. Tighten the two halves of the check valve together.
8. Insert the top of the check valve into the upper air tube.
NOTE: Insert the check valve into the air tube so that the
6
into the packing and try again. If this still does not remove the
packing, use a pick tool to pull the packing out.
installing the new packing.
not tighten.
and thread on the retaining nut.
attached. Slide the needle with the spring and the rear
air valve seal through the needle guide shaft and into the
packing nut. Tighten the material flow adjustment housing
securely using a wrench.
then loosen the packing nut a quarter turn.
into the gun body and tighten into position.
attaching the snap rings.
the needle sticks, loosen the packing nut. If the packing leaks,
tighten the packing nut.
type of material being used.
check valve but do not scratch it.
valve as shown.
arrow on the valve points toward the gun.
© Titan Tool Inc. All rights reserved.
Packing Hole
Packing Nut