Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
AREAS
04
*
MODIFY AREA 01
AREA 01
*
DESCRIPTION 01
AREA 01
*
Example:
If you want to create a system with two areas:
•
Area 1 = LIVING AREA
•
Area 2 = BEDROOM AREA
You must:
MODIFY
SYSTEM
*
MANAGED AREAS
##-
MODIFY AREA 01
AREA 01
*
DESCRIPTION 01
AREA 01
*
MODIFY AREA 02
AREA 02
*
DESCRIPTION 02
AREA 02
*
Programming Scenarios
Scenarios are groups of operations set by the Installer which allow
the User, via the control unit, keypad, reader or telephone, to:
•
turn areas on/off
•
activate / deactivate outputs
Some scenarios are pre-set at the factory .
CREATING SCENARIOS
Up to 16 customised scenarios can be created and then associated
individually or all together with one or more control devices
assigned an address in the Control unit (keypads, readers and
remote controls) .
STEP 1: Selecting scenario
1 .
Go into the Technical Menu .
(▲)/(▼)
2 .
With
select
SCENARIOS
(▲)/(▼)
3 .
With
select the scenario to create / modify
(
indicates the index number of the scenario)
MODIFY SCENAR. XX
XX
and press (*) .
SCENARIOS
03
*
MODIFY SCEN.XX
SCENARIO XX
▼ ▲
▼ ▲
▼ ▲
AREA 01
*=OK #=ESC
LIVING AREA
*=OK #=ESC
▼ ▲
▼ ▲
▼ ▲
AREA 01
*=OK #=ESC
LIVING AREA
*=OK #=ESC
▼ ▲
▼ ▲
AREA 02
*=OK #=ESC
BEDROOM AREA
*=OK #=ESC
and press (*) .
▼ ▲
▼ ▲
STEP 2: Operation on areas (not available in EASY mode)
Defines the operation to be carried out on the areas (switch on / off) .
1 .
Staying in the Scenario Menu .
(▲)/(▼)
2 .
With
select
AREA OPERATION
(+)/(‒)
3 .
With
set the parameter
classic scenario; it lets you set the on/off status of the control
unit "exactly" as described by
will switch on and those deselected will switch off .
AREA OPERATION XX
EXACT ON+OFF
STEP 3: Associated areas
(
)/(
)
1 .
With
select
ASSOC. AREAS
▲
▼
(1)/(2)/(3)
2 .
Press the number key
area to be associated (
= enabled,
#
ASSOC. AREAS XX
---
ASSOC. AREAS XX
###
STEP 4: Operation on outputs (not available in EASY mode)
Defines the operation to be carried out on an output (ON/OFF) when
the scenario is launched .
1 .
Staying in the Technical Menu .
(
)/(
)
2 .
With
select
OUTPUT OPERAT.
▲
▼
(+)/(–)
3 .
With
set the parameter to
narios concern only the areas, if you need to activate an output
do the following:
a .
Set
to
OUTPUT OPERAT.
ON
(
)/(
)
b .
With
select
ASSOC. OUTPUT
▲
▼
(+)/(–)
c .
With
set the output to be activated .
OUTPUT OPERAT. XX
DISABLED
ASSOC. OUTPUT XX
NO
STEP 5: Scenario description
1 .
Staying in the Scenario Menu .
(
)/(
)
2 .
With
select
DESCRIPTION
▲
▼
3 .
With the alphanumeric keys you can edit the text .
(#)
4 .
Press
to confirm and go back to the previous menus . Press
(#)
to cancel the change .
DESCRIPTION XX
SCENARIO XX
*
SCENARIO XX
+=OK #=ESC
GOING OUT
+=OK #=ESC
To create the scenario
GOING OUT
• Area 1 = LIVING AREA
• Area 2 = BEDROOM AREA
• Area 3 = PERIMETER
You must:
.
. We will use the
to EXACT ON+OFF
. The areas selected
ASSOC. AREAS
+ -
relating to the address of the
= disabled) .
-
1 2 3
. Normally the sce-
DISABLED
.
.
and press (*) .
which then arms all of the areas:
Publicité
Table des Matières
