Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Example of programming depending on the type of User .
Owners
All
Switching on + off Enabled Enabled
Employees
All
Switching on + off
Cleaning
All
firm
Access
no
control
ENABLING / DISABLING A CODE
Enabling / disabling a code:
1 .
Go into the Technical Menu .
(
)/(
)
and press (*) .
2 .
With
select
CODES
▲
▼
(
)/(
)
3 .
With
select
USER CODES
▲
▼
(
)/(
)
4 .
With
select the
USER CODE
▲
▼
=enabled,
=disabled) .
[-]
(
)/(
)
5 .
With
select
.
STATUS
▲
▼
(+)
6 .
With
it is enabled and with
CODES 16
*
USER CODES
*
CODE 001 [#]
CODE 001
CODE 002 [-]
CODE 002
*
STATUS
DISABLED
STATUS
ENABLED
Acquiring Keys
Because the keys are unique, ex-factory there are no keys stored
in the control unit .
Associating the keys can be done during first switch-on of the con-
trol unit, following the procedure (see section "10 System start-up",
under "SELF-LEARNING MENU"), or later via the technical menu, as
shown below .
Acquiring new key:
1 .
Go into the Technical Menu .
(
)/(
)
and press (*) .
2 .
With
select
KEYS
▲
▼
(
)/(
)
3 .
With
select
SELECT KEY
▲
▼
(
)/(
)
select the key to be learned and press (*) .
4 .
With
▲
▼
(
)/(
)
5 .
With
select
LEARN KEY
▲
▼
6 .
Put the key to be read on the radio keypad and wait for the
keypad display to confirm it has been read .
7 .
On the keypad the words
(#)
will sound . Press
to continue .
(#)
8 .
Press
to quit and go back to the previous menus .
no
Enabled
Only on
no
no
Only on
no
no
and press (*) .
(*)
to be set and press
(–)
it is disabled .
▼ ▲
▼ ▲
▼ ▲
▼ ▲
002
▼ ▲
+
002
and press (*) .
and press (*) .
will appear and the buzzer
KEY SAVED
KEYS
17
*
SELECT KEY
*
*
The use of the transponder key with the reader built into the keypad
replaces the need to enter the user code, except for access to the
user menu, for which entry of the code on the keypad will still be
necessary .
Once the user code is entered, or a transponder key duly registered
with the system is used, it will be possible to:
• Launch scenarios (by pressing the relevant keys),
• Turn off the system (by pressing the key)
(
[#]
From the keypad it is also possible, again via the built-in transpond-
er reader, for keys to be learned and checked .
The areas enabled through the keypad are also valid for the built-in
reader .
When using the keypad, the areas managed are only those the key-
pad and the code entered have in common, while when using the
built-in reader they are those the keypad and the key that has been
read have in common .
Learning remote controls
The remote controls can be learned during first switch-on of the
control unit, following the voice guide (see section "POWER ON
CTR-U ."), or later via the technical menu, as shown below .
Acquiring new remote control
1 .
Go into the Technical Menu .
(
)/(
)
2 .
With
select
▲
▼
(
)/(
)
3 .
With
select the remote control to be programmed and
▲
▼
press (*) .
(
)/(
)
4 .
With
select
▲
▼
5 .
Briefly press the
6 .
The control unit saves the new remote control (if one had been
acquired previously, the new one overwrites the old one) .
7 .
If the remote control has already been saved, the keypad dis-
plays
TRANSMITTER ALREADY SAVED
TRANSMITTERS 18
*
TRANSMITTER XX
TRANSMITTER XX
*
▼ ▲
▼ ▲
KEY 001
KEY 001
▼ ▲
LEARN KEY 001
*=OK #=ESC
*
KEY READING
IN PROGRESS...
KEY
STORED
and press (*) .
TRANSMITTERS
and press (*) .
SELF-LEARN.
button on the remote control .
.
▼ ▲
▼ ▲
SELF-LEARN.
XX
▼ ▲
*=OK #=ESC
*
PRESS BUTTON
OK PRESS *
Publicité
Table des Matières
