Haverland RC 4 E Manuel D'installation Et Utilisation page 30

13 : 00
Press the OK button to accept the
hour.
Now we are going to introduce the start of the Second
00 : 00
Economy period from Monday to Friday. The Economy,
Second Period P2 and days from Monday to Friday leds will
light up. In our case, the second period starts at 14:00.
L
P2
M
Press the buttons
X
J
V
Press the OK button to accept the
14 : 00
hour.
The following step is to introduce the starting of the Third
00 : 00
Comfort period from Monday to Friday. The Comfort, Third
Period P3 and days from Monday to Friday leds will light up. In
our case, the third comfort period starts at 18:30.
L
P3
M
X
Press the buttons
J
V
Press the OK button to accept the
18 : 30
hour.
Now we are going to introduce the start of the Third Economy
00 : 00
period from Monday to Friday. The Economy, Third Period
and days from Monday to Friday leds will light up. In our case
the period of economy starts at 23:00.
L
P3
M Press the buttons
X
J
V
Press the OK button to accept the
23 : 00
hour. We have programmed the
transmitter from Monday to
Friday.Now we are going to
programme it from Saturday to
Sunday.
Now if you wish, you can programme the period regarding
00 : 00
Saturday to Sunday. IN CASE YOU DO NOT WISH
PROGRAMME SOME PERIOD, YOU MUST PUT THE HOUR
OF THIS PERIOD AT 00:00
S
P1
D
The programming of the WEEKEND PLAN "PLAN FS" is
done in the same way as the programming of the
configurable plan ( See table 1, page 4).
As you can see in the Programme Table, we have not defined
a Third Period between Saturday and Sunday. If you wish you
can programme as many periods you want between Monday
and Friday or between Saturday and Sunday.
------------
When you finish programming, press the button PROG.
The room temperature will appear on the display. You have just
designed a heating system plan in a simple and easy way.
Design your own heating plan based on your needs making a
19.0 C
programming table as we have done in this above stated
example.
OK
OK
OK
OK
PROG
SWITCHING OFF THE LUMINOUS DISPLAY
If you wish you can switch off the luminous display even
though the transmitter is working. This option can be used
in situations if the light given out by the display bothers at
night in the bedrooms for example. This can be done in
the following way:
23.0 C
The room temperature appears on the display. To switch off the
display press the button
.
The luminous display will be switched off maintaining an
intermittent point on the right side of the display WHEN THE
TRASMITTER IS HEATING and the light indicators of Comfort
or Economy or that of the Manual position will also be on.
If you wish to illuminate the display again, press any search
23.0 C
button.
Important Note: This option is cancelled when the thermal
transmitter is programmed in the Anti-freeze Plan "PL AH".
MODIFICATION OF A PARAMETER OF A
CONFIGURABLE PLAN
Whenever you wish to modify any parameter of a plan
configured by you IT IS NOT NECESSARY TO RE-
PROGRAMME THE FULL CONFIGURABLE PLAN.
To explain how to modify a parameter we are going to
explain it using a practical example. We are going to
change "the starting hour of the Second Comfort Period
from Saturday to Sunday". As you can see on the Table
above, the starting hour is 14:00. We are going to change
it to 15:00.
These are the steps to follow :
The room temperature will appear on the display.
23.0 C
Press the button PROG 1,5 sec..
Follow the initial steps explained earlier to undertake a
Configurable Plan till "PL:CF" appears on the display.
Once this appears, press OK as many times as needed till
PL : C F
the Comfort, Second Period P2 and days Saturday to
Sunday leds light up. "14:00" should appear on the display.
14 : 00
Now we are going to change the time 14:00 to 15:00.
Press the buttons
S
P2
D
Once "15:00" appears on the display, press the button "PROG"
15 : 00
to accept the modification. You have just changed the
parameter in a simple way.
PROG
PROG