Publicité
Les langues disponibles
Les langues disponibles
English
WARNING: To reduce the risk of personal injury,
ALWAYS ensure workpiece is anchored or clamped firmly.
If drilling thin material, use a wood "back-up" block to
prevent damage to the material.
Turn the collar to the drill bit symbol for drilling. Select the
desired speed/torque range using the gear shifter to match the
speed and torque to the planned operation.
1. Use sharp drill bits only. For WOOD, use twist drill bits, spade
bits, or hole saws. For METAL, use high-speed steel (HHS)
twist drill bits or hole saws.
2. Always apply pressure in a straight line with the bit. Use
enough pressure to keep drill biting, but do not push hard
enough to stall the motor or deflect the bit.
3. Hold tool firmly with both hands to control the twisting
action of the drill.
WARNING: The drill may stall if overloaded causing a
sudden twist. Always expect the stall. Grip the drill firmly
with both hands to control the twisting action and
avoid injury.
4. iF DRill sTAlls, it is usually because it is being overloaded
or improperly used. RElEAsE TRiggER iMMEDiATElY,
remove drill bit from work, and determine cause of stalling.
DO nOT CliCK TRiggER On AnD OFF in An ATTEMPT
TO sTART A sTAllED DRill — This CAn DAMAgE
ThE DRill.
5. To minimize stalling or breaking through the material,
reduce pressure on drill and ease the bit through the last
fractional part of the hole.
6. Keep the motor running when pulling the bit back out of a
drilled hole. This will help prevent jamming.
7. With variable speed drills there is no need to center punch
the point to be drilled. Use a slow speed to start the hole
and accelerate by squeezing the trigger harder when the
hole is deep enough to drill without the bit skipping out.
Operation as a Screwdriver
Select the desired speed/torque range using the dual range
gear shifter on the top of tool to match the speed and torque to
the planned operation.
Insert the desired fastener accessory into the chuck as you
would any drill bit. Make a few practice runs in scrap or unseen
areas to determine the proper position of the clutch collar.
MAXIMUM RECOMMENDED CAPACITIES
Low Range–1
Bits, Metal Drilling
6.35 mm
Wood, Flat Boring
19.05 mm
Hole Saws
19.05 mm
MAINTENANCE
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
10
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by D
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
High Range–2
This long life battery pack must be recharged when it fails
3.18 mm
to produce sufficient power on jobs which were easily done
12.7 mm
before. At the end of its technical life, discard it with due care for
our environment:
15.88 mm
•
Run the battery pack down completely, then remove it from
the tool.
•
Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
WALT, have not been tested with this product, use
e
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
WALT recommended
e
Publicité
