Bosch EXACT ION 18 V-LI 6-1500 WK Notice Originale page 19

Removing the application tool
– Pull the application tool (1) off of the tool holder (2), us-
ing pliers if necessary.
Changing the tool at the screw head with quick-
change chuck (see figure G)
Inserting the application tool
Only use application tools with the matching shank (1/4"
hexagon).
– Pull the sleeve of the quick-change chuck (23) forwards.
– Place the application tool (1) into the tool holder (2) and
release the quick-change chuck again.
Removing the application tool
– Pull the sleeve of the quick-change chuck (23) forwards.
– Take the application tool (1) out of the tool holder (2) and
release the quick-change chuck again.
Operation
Starting Operation
Always set the rotational direction using the rotational direc-
tion switch (9) before starting the power tool:
The power tool will not start if the rotational direction switch
(9) is in the centre (lock-off button).
Setting the rotational direction (see figure H)
– Clockwise: To drive in screws, press the rotational direc-
tion switch (9) through as far as possible to the left.
– Anti-clockwise: To loosen or unscrew screws, press the
rotational direction switch (9) through as far as possible
to the right.
Switching on the worklight
The worklight (6) illuminates the work area in poor lighting
conditions. Switch on the worklight (6) by lightly pressing
the on/off switch (8). If you press down harder on the on/off
switch, the power tool will switch on and the worklight will
remain illuminated.
Do not look directly into the worklight; it can blind
u
you.
Switching on/off
The screwdrivers have a torque-dependent
shut-off clutch that can be set to a value in the
specified range. The clutch is triggered when
the set torque is reached.
– To switch on the power tool, press the on/off switch (8)
down fully.
– The power tool will switch off automatically when the
set torque is reached.
If the on/off switch (8) is released too early, the pre-
u
set torque will not be reached.
Practical advice
Only apply the power tool to the screw/nut when the
u
tool is switched off. Rotating tool inserts can slip off.
Bosch Power Tools
Adjusting the torque (see figure I)
The torque depends on the spring preload of the shut-off
clutch. The shut-off clutch triggers both in right and left rota-
tion upon reaching the set torque.
Only use the supplied adjustment tool (24) to set the indi-
vidual torque.
– Slide the slider (7) on the power tool back completely.
– Insert a hex key (25) into the application tool (24) and
turn it slowly.
– Once a small protrusion (setting disc (26)) can be seen in
the clutch within the opening of the housing, insert the
adjustment tool (24) into this protrusion and turn it.
Note: The required setting is dependent from the type of
threaded connection and can be best determined by prac-
tical trials. Check a trial screw application with a torque
spanner.
If you set the torque to a value outside the specified
u
power range, the shut-off clutch will not be triggered.
Marking the torque setting (see figure J)
Always use the power tool with a marking ring to be certain
that the housing is protected against dust and dirt.
To label individually set torques, you can replace the mark-
ing ring (18) with a marking ring of a different colour.
– Press the marking ring (18) with a thin screwdriver blade,
a spatula or similar implement.
Screwdriving indicator (green/red LED)
The shut-off clutch is triggered upon reaching the preset
torque. The LED indicator (11) lights up green.
If the preset torque has not been reached, the LED indicator
(11) lights up red and the tool emits a sound. The screw
must be driven in again.
Repeat protection
If the shut-off clutch is triggered while driving a screw, the
motor will switch off. You will need to wait 0.7 seconds be-
fore you can switch the tool on again. This prevents you from
accidentally retightening screws that are already firmly in
place.
Maintenance and Service
Maintenance and Cleaning
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
Lubricating the power tool
Lubricant:
Special gearbox grease (225 ml)
Article number 3 605 430 009
Molykote grease
Motor oil SAE 10/SAE 20
English | 19
1 609 92A 6N3 | (09.09.2021)