Bosch EXACT ION 18 V-LI 6-1500 WK Notice Originale page 18

18 | English
To remove the battery (12), press the release button (13)
and pull the battery forward and out of the power tool. Do
not use force to do this.
Battery charge indicator (yellow LED)
Battery Meaning
charge indic-
ator (10)
Flashing Charge the battery:
light + sound You can only drive in six to eight more
screws.
Continuous There is not enough capacity left to drive in
light another screw or the power tool has over-
loaded:
The power tool can no longer be switched
on.
– Remove the battery and replace it with a
battery that is fully charged.
Flashing The power tool has overheated and
light switched itself off:
– Wait a short while for the light to stop
flashing before switching the power tool
on again.
Operating and storage conditions
The power tool is suitable only for operation at enclosed
work sites.
To ensure smooth operation, the permitted ambient temper-
ature should be between 0 °C and +45 °C, at a permitted rel-
ative humidity of between 20 and 95%, free of condensa-
tion.
Suspension device (see figure B)
You can use the hanging hook (15) to attach the power tool
to a suspension device.
– Place the hanging hook (15) on the power tool and click it
into the slots (16).
Regularly check the condition of the hanging hook and
u
the catch in the suspension device.
Switching on the worklight (see figure C)
– Press the marking ring (18) with a thin screwdriver blade,
a spatula or similar implement.
– Slide the spring ring(19) back onto the housing shell us-
ing a pair of spring ring pliers.
The two shell halves of the LED holder (17) that encase the
worklight (6) can now be brought into the required position.
– Taking care not to damage the cable on the worklight,
slide it into the cavity provided for it (20) in the housing
shell without allowing it to bend.
– Encase the worklight (6) in the two housing shells of the
LED holder (17) once again.
– Press the spring ring (19) and the marking ring (18) back
into their original position.
1 609 92A 6N3 | (09.09.2021)
Configuring the power tool
You can configure various settings on the power tool (e.g. ro-
tational speed, screwing stage, repeat protection) using
BOSCH EXACT Configurator software. The power tool must
be connected to a PC via its USB port in order to do this.
Note: Follow all the safety instructions and information in
the software manual.
Fitting the angled screw head (see figure D)
For these industrial cordless angle wrenches, a suitable
angled screw head (see "Technical data", page 16) must first
be fitted.
– Use the open-ended spanner (22) on the spanner flat (4)
of the angled head flange of the power tool to hold it in
place.
Never clamp the power tool to the housing shells.
u
– Place the angled screw head (3) into the required posi-
tion on the flange and use the open-ended spanner (21)
on the spanner flat (5) of the cap nut to tighten it.
While doing this, use the open-ended spanner (22) on the
angled head flange to provide resistance.
Adjusting the angled screw head
You can adjust the angled screw head (3) to a total of eight
different positions.
– Use the open-ended spanner (22) on the spanner flat (4)
of the angled head flange of the power tool to hold it in
place.
Never clamp the power tool to the housing shells.
u
– Use an open-ended spanner (21) on the spanner flat (5)
of the cap nut to loosen it. Adjust the angled screw head
(3) by 45° accordingly to the required position and use
the open-ended spanner (21) on the spanner flat (5) of
the cap nut to tighten it again.
While doing this, use the open-ended spanner (22) on the
angled head flange to provide resistance.
Changing the tool at the screw head with
external square (see figure E)
Inserting the application tool
– Press the pin into the square of the tool holder (2), e.g.
using a narrow screwdriver, and slide the application tool
(1) over the square. Ensure that the pin engages in the re-
cess of the application tool.
Removing the application tool
– Press the pin into the recess of the application tool (1)
and pull the application tool off of the tool holder (2).
Changing the tool at the screw head with
internal hexagon (see figure F)
Inserting the application tool
– Insert the application tool (1) into the internal hexagon of
the tool holder (2) until it audibly engages.
Bosch Power Tools