Bosch EXACT ION 18 V-LI 6-1500 WK Notice Originale page 17

Industrial cordless angle wrench EXACT
ION
Straight screw head (included with the
product as standard)
A) measured with Bosch angled screw head
B) Measured at 20–25 °C with rechargeable battery GBA 18V 5.0Ah.
C) Depends on battery in use
D) Limited performance at temperatures < 0 °C
Article number
Torque, hard/soft screwdriving applic-
ation according to ISO 5393
Tightening torque at the flange
Weight according to EPTA-Procedure
01:2014
Noise/Vibration Information
Noise emission values determined according to
EN 62841-2-2.
Typically, the A-weighted sound pressure level of the power
tool is 70 dB(A). Uncertainty K = 3 dB. The noise level when
working can exceed 80 dB(A).
Wear hearing protection
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-2:
Tightening screws and nuts of the maximum permitted size:
2 2
a < 2.5 m/s , K = 1.5 m/s ,
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Bosch Power Tools
6–1500 WK
−
Angled screw Angled screw
head head
■ 1/4" ■ 3/8"
0 607 453 0 607 453
617 620
Nm 20 20
Nm 20 20
kg 0.21 0.21
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Charging the Battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the battery (see figures A1–A2)
The battery (12) is equipped with two locking levels to pre-
vent the battery from falling out when pushing the battery re-
lease button (13) unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
8–1100 WK 12–700 WK
− −
Angled screw Angled screw
head head
1/4" quick-change
chuck 1/4"
0 607 453 0 607 453
618 630
20 20
20 20
0.22 0.21
1 609 92A 6N3 | (09.09.2021)
English | 17
12–450 WK
−
Straight
screw head
quick-change
chuck 1/4"
0 607 453
631
6
10
0.21