EINHELL GC-SC 18/28 Li Instructions D'origine page 23

Charging the battery (Fig. 10)
The equipment is supplied without batteries and
without a charger!
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock buttons (Fig.
11/Item C).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(22) into the socket outlet. The green LED will
then begin to fl ash.
3. Insert the battery pack (21) into the battery
charger (22).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Battery capacity indicator (Fig. 11)
Press the switch for the battery capacity indicator
(Item A). The battery capacity indicator (Item B)
shows the charge status of the battery using 3
LEDs.
Anl_GC_SC_18_28_Li_Solo_SPK13.indb 23 Anl_GC_SC_18_28_Li_Solo_SPK13.indb 23
GB
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
Fitting the battery (Fig. 12 – 13)
Note: The battery cover is self-closing and is held
shut by 2 magnets. If the safety plug (Item 15)
is already installed, remove it before fi tting the
battery.
•
Open the battery cover (Item 6) and hold
it open. Push the battery (Item 21) into the
mount until you hear the battery engage.
6. Operation
Caution!
The scarifi er is equipped with a safety switch to
prevent unauthorized use. Directly before starting
up the scarifi er insert the safety plug (Fig. 13/Item
15) and remove the safety plug again when inter-
rupting or terminating your work.
To prevent accidental start-up of the scarifi er, the
push bar (Fig. 14/Item 3) is equipped with a safety
lock-off (Fig. 14/Item 2) which must be pressed
before the lever switch (Fig. 14/Item 1) can be
pressed. The start time for the equipment can
amount to several seconds. If the lever switch is
released, the scarifi er switches off . Repeat this
process several times so that you are sure that
your equipment functions properly. Always pull
out the safety plug before performing any adjus-
ting, repair, maintenance or cleaning work on the
equipment. Make sure that the spike drum is not
rotating.
Danger! Never open the ejector fl ap when the
motor is running. A rotating cutting unit can cause
injuries. Always fasten the ejector fl ap carefully.
- 23 -
07.09.2021 16:13:13 07.09.2021 16:13:13