Maintenance; General; Daily Cleaning; Monthly Cleaning - Hatco IHDCH Série Manuel D'installation

MAINTENANCE

General

Hatco Intelligent Heated Display Cabinets are designed for
maximum durability and performance, with minimum maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and
allow unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• This unit is not "jet-proof" construction. Do not use jet-
clean spray to clean this unit.
• Do not steam clean or use excessive water on unit.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
This unit has no "user-serviceable" parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.

Daily Cleaning

To maintain performance and preserve the finish of the cabinet,
it is recommended that the unit be cleaned daily.
NOTICE
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
1. Move the Power I/O (on/off) switch to the O (off) position
and unplug the power cord. Allow the unit to cool.
2. Remove and clean all internal components.
• Components include risers, product supports arms,
shelves, front and rear vent covers, crumb trays (located
directly below the front and rear vent covers), and the
decorative base pieces.
• Clean and sanitize the components in a 3-compartment
sink, and allow to air dry.
NOTE: The above listed components are dishmachine-safe.
Not all dishmachine detergents have been tested. If a
noticeable change in color or gloss occurs, an alternate
detergent should be used.
3. Wipe down all interior and exterior metal surfaces using a
clean, damp, non-abrasive cloth. A non-abrasive cleaner
may be used for difficult stains. Hard to reach areas should
be cleaned using a small brush and mild soap.
4. Clean all glass panels and glass doors using a standard
glass cleaner.
5. Clean polycarbonate sliding doors using soft, microfiber
cleaning cloths, mild soap, and water. NOTICE: Do not
use paper towel or glass cleaner on plastic surfaces—
scratching or damage may occur.
6. Spray all interior and exterior surfaces with sanitizing
solution and allow to air dray.
7. Reassemble the unit.
Front Vent
Cover
Base
Pieces
Front Crumb Tray
(under vent cover)
Removing/Installing Components (IHDCH-45 shown)

Monthly Cleaning

Use the following procedure for periodic cleaning and deliming
of the atomizer pans.
NOTE: The lime and mineral content of the water used for
daily operation will determine how often the deliming
procedure must be performed.
NOTE: Perform this procedure when the unit will not be used
for a period of time, such as the end of the day.
1. Move the Power I/O (on/off) switch to the O (off) position and
unplug the power cord. Allow the unit to cool completely.
2. Perform steps 2–5 of the "Daily Cleaning" procedure.
3. Remove both atomizer pans (refer to the "Removing the
Atomizer Pans" procedure in the INSTALLATION section
of this manual).
4. Fill an appropriate container with a mixture of 75% water
and 25% white vinegar. Do not use flavored vinegar.
5. Place both atomizer pans into the vinegar solution and
allow to soak for several hours, preferably overnight.
6. Remove both atomizer pans from the vinegar solution and
clean using warm, soapy water and a soft cloth.
7. Rinse both atomizer pans with clean water, and allow to air
dry.
8. Install the cleaned atomizer pans into the unit (refer
to the "Installing the Atomizer Pans" procedure in the
INSTALLATION section of this manual).
9. Spray all interior and exterior surfaces with sanitizing
solution and allow to air dry.
10. Reassemble the unit.
10
English
Rear Vent Cover
Front glass removed for clarity.
All components removed
through rear sliding door.
Form No. IHDCH45M-0619
Rear
Crumb
Tray