Changing The Timer Settings; Changing Between Celsius And Fahrenheit; Updating The Firmware - Hatco IHDCH Série Manuel D'installation

English
2. Touch the key.
• Enter the password "248"
using the number keys that
appear.
• The Service screen will
appear on the display.
3. Touch the TEMPHUMID key
on the Service screen to
access the air temperature and relative humidity settings.
4. Adjust the air temperature and/or relative humidity settings.
• Touch the red
key on the left side of the
display to set the desired
air temperature.
• Touch the blue
key on the right side of the
display to set the desired
relative humidity (RH).
NOTE: Air temperature and humidity settings may vary
depending upon product make-up and consistency.
5. Touch the key to save the settings and return to the
Home Screen.

Changing the Timer Settings

Use the following procedure to change the time setting on each
of the product timers.
1. Move the Power I/O (on/off) switch to the I (on) position.
• The unit will turn on and the touchscreen controller will
energize and show the Home Screen.
2. Touch the key.
• Enter the password "248" using the number keys that
appear.
• The Service screen will appear on the display.
3. Touch the TIMERS key on the Service screen to access
the Timers screen.
NOTE: The check boxes on the
Timers screen correspond
with each available product
timer, when viewing unit
from the operator side.
Touch the appropriate check
box to toggle the timer
between visible and invisible
on the Home screen.
4. Touch the MAXSETTING key on the Timers screen to
access the timer settings.
a. Touch the SET key to
highlight the first timer
setting.
b. Touch the red or
on the display to change the
timer setting.
c. Touch the next desired timer
setting to make it active for
change, and repeat the previous step to change the setting.
d. Touch the DONE key when timer setting changes are
complete.
Form No. IHDCH45M-0619
Service
Firmware Usage
Control Timers
Testmode TempHumid
or
180˚ 17%
or
Timers
Select Config
(Max 8 timers)
MaxSetting
0:40 0:40
0:40 0:40
0:40 0:40
key
Set
5. Touch the key to save the settings and return to the
Home Screen.

Changing Between Celsius and Fahrenheit

Use the following procedure to change the air temperature unit
of measure between Celsius and Fahrenheit.
1. Move the Power I/O (on/off) switch to the I (on) position.
• The unit will turn on and the touchscreen controller will
energize and show the Home Screen.
2. Touch the key.
• Enter the password "248"
using the number keys that
appear.
• The Service screen will
appear on the display.
3. Touch the CONTROL key on
the Service screen to access
the Control Settings screen.
4. Choose the desired unit of measure on the "Units" line:
• Touch the "F" box to select
Fahrenheit.
• Touch the "C" box to select
Celsius.
NOTE: The box for the active unit
of measure is highlighted in
green.
5. Touch the key to save the settings and return to the
Home Screen.

Updating the Firmware

Use the following procedure to perform a firmware update on
the touchscreen controller.
1. Move the Power I/O (on/off) switch to the I (on) position.
• The unit will turn on and the touchscreen controller will
energize and show the Home Screen.
2. Touch the key.
• Enter the password "248" using the number keys that
appear.
• The Service screen will appear on the display.
3. Touch the FIRMWARE key on the Service screen to access
the Firmware Update screen.
4. Insert the USB drive into the
USB port next to the controller,
and touch the UPDATE key on
the Firmware Update screen.
• The update will begin. When
complete, the touchscreen
controller will restart and
show the Home screen.
9
OPERATION
Service
Firmware Usage
Control Timers
Testmode TempHumid
Control Settings
Units F C
Version 01.00.27
SWHHID45PH0201
Firmware Update
Plug-in the USB stick, then
press the Update button.
Update