Important Safety Information; Electric Shock Hazard; Fire Hazard - Hatco IHDCH Série Manuel D'installation

English
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
WARNING

ELECTRIC SHOCK HAZARD:

• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• Turn OFF power switch, unplug power cord, and
allow unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
• This unit is not "jet-proof" construction. Do not use jet-
clean spray to clean this unit.
• Do not steam clean or use excessive water on unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power
cord. Cord must be replaced by Hatco, an Authorized
Hatco Service Agent, or a person with similar
qualifications.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.

FIRE HAZARD:

• Install unit on non-combustible surface only.
• Locate unit a minimum of 1" (25 mm) from combustible
walls and materials. If safe distances are not maintained,
discoloration or combustion could occur.
• Do not place anything on top of unit.
Make sure food product has been heated to the proper
food-safe temperature before placing in unit. Failure to
heat food product properly may result in serious health
risks. This unit is for holding pre-heated food product only.
Hatco Corporation is not responsible for actual food
product serving temperature. It is the responsibility of the
user to ensure that food product is held and served at a
safe temperature.
The light fixtures in this unit have safety shields covering
the light bulbs to meet National Sanitation Foundation
(NSF) standards. To avoid personal injury and/or food
contamination, always operate the unit with the safety
shields properly installed.
Form No. IHDCH45M-0619

IMPORTANT SAFETY INFORMATION

Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from the unit.
This unit has no "user-serviceable" parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
BURN HAZARD:
• Some exterior surfaces on the unit will get hot. Use
caution when touching these areas.
• Do not remove or adjust atomizer pans when unit is
hot. Allow unit to cool completely before working with
atomizer pans.
Locate unit at proper counter height in an area that is
convenient for use. Location should be level to prevent
unit or its contents from falling accidentally and strong
enough to support the weight of the unit and contents.
The National Sanitation Foundation (NSF) requires that
units over 36" (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above the
installation surface.
Do not move or relocate the unit for cleaning. The unit is
bulky and heavy.
Transport unit in upright position only. Before moving
unit, secure all glass surfaces, doors, and support arms
with tape. Failure to do so may result in damage to unit or
personal injury.
Do not locate unit in area with excessive air movement
around unit. Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods, air
conditioning ducts, and exterior doors).
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
IMPORTANT—DO NOT use paper towel or glass cleaner to
clean plastic surfaces such as sliding doors. Paper towel
and glass cleaner may scratch the material. Wipe off plastic
surfaces using a soft, clean, water-dampened cloth.
Use detachable hose sets supplied with unit. Do not use
old hose sets.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
3
WARNING
CAUTION
NOTICE