Télécharger Imprimer la page

DeWalt DWE4202 Traduction De La Notice D'instructions Originale page 49

Masquer les pouces Voir aussi pour DWE4202:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

• Young children and the infirm. This appliance
is not intended for use by young children or
infirm persons without supervision.
• This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
Anti-vibration Side Handle
The anti-vibration side handle offers added comfort
by absorbing the vibrations caused by the tool.
Dust Ejection System (fig. 1)
The dust ejection system (K) prevents dust pile-up
around the guard and motor inlet, and minimises the
amount of dust entering the motor housing.
Soft Start Feature
DWE4206, DWE4207, DWE4216, DWE4217
The soft start feature allows a slow speed build-up
to avoid an initial jerk when starting. This feature is
particularly useful when working in confined spaces.
No-Volt
DWE4206, DWE4207, DWE4216, DWE4217
The No-volt function stops the grinder restarting
without the switch being cycled if there is a break in
the power supply.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your D
WALT tool is double insulated in
e
accordance with EN 60745; therefore no
earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
D
WALT service organisation.
e
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power input
of this tool (see Technical Data).The minimum
conductor size is 1.5 mm
2
is 30 m.
When using a cable reel, always unwind the
cable completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
Attaching Side Handle (fig. 1)
WARNING: Before using the tool, check
that the handle is tightened securely.
Screw the side handle (C) tightly into one of the
holes on either side of the gear case. The side
handle should always be used to maintain control of
the tool at all times.
Accessories and Attachments
It is important to choose the correct guards,
backing pads and flanges to use with grinder
accessories. Refer to chart at the end of this section
for information on choosing the correct accessories.
NOTE: Edge grinding can be performed with
Type 27 wheels designed and specified for
this purpose.
WARNING: Accessories must be rated
for at least the speed recom mended on
the tool warning label. Wheels and other
accessories running over rated accessory
speed may burst and cause injury.
Threaded accessories must have a M14
hub. Every unthreaded accessory must
have a 22 mm arbor hole. If it does not,
it may have been designed for a circular
saw and should not be used. Use only
the accessories shown in the chart at the
end of this section. Accessory ratings
must be above listed minimum wheel
speed as shown on tool nameplate.
english
; the maximum length
47

Publicité

loading