Attaching The Hose - Black & Decker FSMH1321 Traduction De La Notice D'instructions Originale

ENGLISH
Attaching the carpet glider (12d) (For use on
carpets only)
Place the carpet glider (12d) on the floor.
u
Attach a cleaning pad to the floor cleaning head (12,12a)
u
Lightly press the steam mop down onto the carpet glider
u
(12d) until it clicks into place.
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Removing the carpet glider
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or
open toed footwear.
Return the handle (8) to the upright position and turn the
u
steam mop 'OFF'.
Wait until the steam mop cools down (approximately 5
u
minutes).
Place the front of your shoe onto the carpet glider removal
u
tab and press down firmly.
Lift the steam mop up and off the carpet glider.
u
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
The Delta Head (Fig. D)
This steam mop incorporates a built-in delta head which
enables you to access tight corners and narrow spaces.
Caution! Always wear suitable shoes when accessing the
delta head on your steam mop. Do not wear slippers or
open-toed footwear.
Turn the steam-mop to 'OFF'
u
Wait until the steam-mop cools down (approximately five
u
minutes).
Place the front of your shoe onto the steam head removal
u
tab (12c) and press down gently.
Lift the delta head (12b) up off the steam head (12a)
u
Fit the delta head cleaning pad to the bottom of the delta
u
head.
Note: Remove the cleaning pad before refitting the delta
head to the steam head.
To refit the Delta head, place the tip of the Delta head into
u
the steam head then press down firmly ensuring that the
Delta head clicks into place.
12
(Original instructions)
Attaching the hose and accessories to the
hand held steam cleaner (Fig. G - M)
Warning! Inspect the seal between the connection point on
the hand held steam cleaner (5) and the steam hose (16)
before each use. If the seal malfunctions or is damaged,
please contact your nearest authorised repair agent. Do not
use the appliance.

Attaching the hose

Press the steam hose release button (16a) on the steam
u
hose (16).
Connect the steam hose (16) to the hand held steam
u
cleaner (5) and release the steam hose release button
(16a) making sure it clicks into place.
Important! Ensure that the steam hose (16) is securely
connected to the hand held steam cleaner (5). If steam
escapes from the joint, the hose is incorrectly fitted. Switch off,
allow the unit to cool then remove and refit the hose.
Attaching accessories (Fig H)
Align the lugs on the steam nozzle (17) with the recesses
u
on the accessory.
Press the accessory onto the steam nozzle (17) and twist
u
anti-clockwise until the accessory clicks into place.
Important! All accessories, apart from the SteaMitt
which has its own hose and connector (25), must be attached
to the steam hose (16) for use.
Removing the hose and accessories
Warning! The steam hose (16), Steam nozzle (17) and
accessories become hot during use. Allow the unit and all
accessories to cool before attempting to remove.
Removing an accessory
Twist the accessory clockwise then pull away from the
u
hose (16).
Removing the hose
Press the steam hose release button (16a) on the steam
u
hose (16) and pull away from the hand held steam unit.
SteaMitt
TM
Your BLACK+DECKER SteaMitt
TM
sanitising and cleaning tiles, work tops, kitchen surfaces and
bathroom surfaces. This appliance is intended for indoor
household use only.
Attaching the SteaMitt
steam unit
Warning! Inspect the seal on the steam nozzle and hose
before each use. If the seal is missing or damaged then
please contact your nearest authorised repair agent.
(24)
TM
has been designed for
TM
hose to the hand held
TM