Cleaning The Filters - Black & Decker BDPSE3615 Mode D'emploi

ENGLISH
For increased power, slide the variable power switch (2)
u
forward.
Note: The floor brush (8) will power on when it is
attached to the vacuum or extension tube (it can be switched
off by pressing the button 2a on the display). The LED
worklights on the front of the floor head will illuminate
whenever the beater bar activation button (2a) is switched ON
(they can be switched off by pressing the button again).
Note: The state of charge indicator LEDs (3) will
illuminate while the vacuum is ON.
To switch OFF, press the On/Off button (1).
u
Return the battery to the charger immediately after use so
u
that it will be ready and fully charged for the next use.
Using an Accessory tool (Fig. G)
Your vacuum may come with some of the following tools.
2 in 1 Accesssory tool (10)
u
Crevice tool (11).
u
Pet hair tool (13).
u
Wide mouth dust brush (14).
u
The accessory tool (10), (11), (13) or (14) can be fitted
u
either directly to the extension tube (6) or to the vacuum
inlet (5) as shown in Fig. G.
Align the top of the accessory tool (10), (11), (13) or (14)
u
with the vacuum inlet (16) or extension tube connection
(9a) and push into place so it locks into position as shown
in figure G.
Cleaning and emptying the vacuum
Filter agitator (Fig. H)
With the lift away dust canister (6) off the chassis (17) ,
rotate the filter agitator wheel 5 - 10 times to remove exces-
sive dust from the filter thus increasing its performance.
Note: It is recommended that you agitate when the unit is
emptied and the prefilter removed.
Note: Maximum dust collection will only be obtained with
clean filters and an empty dust canister.
If dust begins to fall back out of the product after it is switched
off, this indicates that the dust canister is full and requires
emptying.
To empty the dust canister (Fig. I, J)
Lift and remove the lift away dust canister (6) from the
u
chassis (17) as shown in figure I.
Place the dust canister over a dust bin and press the
u
dust canister lid release button (6a) to empty the dust
canister as shown in figure J.
Close the dust canister lid (7), until it "clicks" firmly
u
into position.
Install the lift away dust canister (6) back onto the
u
chassis (17).
8
(Original instructions)
Removing pre-filter (Fig. K)
Lift and remove the lift away dust canister (6) from the
u
chassis (17) as shown in figure I.
Place the dust canister over a trash bin and press the
u
dust canister lid release button (6a) to empty the dust
canister as shown in figure J.
Use your index finger and thumb to pinch the pre-filter
u
(18), pull the pre-filter (18 ) from the dust canister (6) as
shown in figure K.
Note: The filter housing fits snuggly in the dust canister
and may be difficult to remove at first.
Empty the dust canister.
u
Install the pre-filter (18) into the dust canister (6)
u
ensuring the dust canister tab (20) aligns with the prefilter
slot (19) as shown in figure K.
Install the dust canister onto the vacuum, until it "clicks"
u
firmly into position.
Removing filter (Fig. L)
Lift and remove the lift away dust canister (6) from the
u
chassis (17) as shown in figure I.
Place the dust canister over a trash bin and press the
u
dust canister lid release button (6a) to empty the dust
canister as shown in figure J.
Grasp the agitator wheel housing (21) and pull up
u
to remove.
Remove the filter (22), from the agitator wheel housing
u
(21) as shown in figure L.
Shake off or lightly brush any loose dust from the filter.
u
Install the the filter (22), into the agitator wheel
u
housing (21).
Install the agitator wheel housing (21) onto the dust
u
canister, until it "clicks" firmly into position.

Cleaning the filters

Once the filter and pre-filter are removed from the dust
u
canister shake off or lightly brush any loose dust from
the pre-filter and filter.
Rinse out the dust canister (6) with warm soapy water.
u
Wash the filters with warm soapy water.
u
Ensure the filters are completely dry before refitting
u
(24hrs).
Follow instructions in the "Removing pre-filter and
u
Removing filter" sections for assembly instructions.
Note: Maximum dust collection will only be obtained with
clean filters and an empty dust canister.
If dust begins to fall back out of the product after it is
switched off, this indicates that the dust canister is full
and requires emptying or that there is a blockage somewhere.
Wash the filters regularly using warm, soapy water and
u
ensure that they are completely dry before using again.
The cleaner the filter is, the better the product will perform.