Cleaning And Maintenance; Protecting The Environment - Black & Decker PAV1205 Mode D'emploi

ENGLISH
lock button (3) and rotate the dust collector to
the required position.
• Release the collector lock button (3) to lock the
dust collector (8) in position.
• The dust collector (8) can be extended by
pulling the dust collector extension (7) until it
locks into position.
• The extension can be retracted by pressing the
button (14) and pushing the extension (7) back
into the dust collector.
• The dust collector (8) should be returned to the
storage position under the appliance after use.
Fitting the accessories (fi g. C & D)
The appliance is supplied with the following
accessories:
• Two brush tools (10 & 11) for upholstery
• An extension hose (12)
• A hose connector (13)
Note: The brush tool (10) can be fi tted into the
front of the appliance, the right-angled brush tool
(11) can be fi tted to the end of the extension hose
(12).
To fi t an accessory, proceed as follows:
• Insert the brush (10) into the front of the
appliance.
• Alternatively, fi t the hose connector (13) onto
the nose of the appliance and attach one end
of the hose (12) to the connector.
• Attach the right-angled brush tool (11) to the
other end of the hose.
• When not in use, the accessories can be stored
in the storage bag (9).
Use
Connecting to the vehicle's power supply
(fi g. E)
• Make sure that the appliance is switched off.
• Remove the cigarette lighter from it's socket.
• Plug the connector (6) into the cigarette lighter
socket.
Switching on and off (fi g. F)
• To switch on, slide the on/off switch (4) forward.
• To switch off, slide the on/off switch back.
The appliance can be used for periods of up
to 30 minutes without noticeably affecting the
power of a normally charged car battery in good
condition.
Warning! Extended use will drain the battery
power. Do not run the vehicle's engine while
cleaning as this can shorten the life of the
appliance.
6
Optimising the suction force (fi g. G)
In order to keep the suction force optimised, the
fi lters must be cleared regularly during use.
• Rotate the fi lter cleaning wheel (5) a few turns
to shake out dust clogging the fi lters (15 & 16).

Cleaning and maintenance

Warning! Regularly clean the fi lters (15 & 16).
Cleaning the dust bowl and fi lters (fi g. H - I)
The fi lters are re-usable and should be cleaned
regularly.
• Press the release latch (1) and open the
container door (2) (fi g. H).
• Empty the dust container.
• Remove the fi lters (15 & 16) by twisting them
counterclockwise (fi g. I).
• Brush any loose dust off the fi lters.
• Wash the fi lters in warm, soapy water (fi g. J).
• Make sure that the fi lters are dry.
• Refi t the fi lters (15 & 16) on to the appliance,
twisting them clockwise until they lock into
place.
• Close the container door (2). Make sure that
the release latch (1) clicks into place.
Warning! Never use the appliance without
the fi lters. Optimum dust collection will only be
achieved with clean fi lters.
Replacing the fi lters
The fi lters should be replaced every 6 to 9 months
and whenever worn or damaged. Replacement
fi lters are available from your Black & Decker
dealer (cat. no. VF50):
• Remove the old fi lters as described above.
• Fit the new fi lters as described above.

Protecting the environment

Separate collection. This product must
not be disposed of with normal household
waste.
Should you fi nd one day that your appliance
needs replacement, or if it is of no further use to
you, think of the protection of the environment.
Black & Decker repair agents will accept old
Black & Decker tools and ensure that they are
disposed of in an environmentally safe way.
Separate collection of used products and
packaging allows materials to be recycled
and used again. Re-use of recycled
materials helps prevent environmental
pollution and reduces the demand for raw
materials.