Programming The Sim Via Pc; Introduction; Preliminary Operations; Folders - DSC GS3050-A Mode D'emploi

The GS3050-A SIM-CARD can be program-
med via the GS3050-A Software Application
(this method is strongly advised), or via any
GSM Cellphone.
The following sections provide the relative in-
structions.
G G G G G In MANUAL mode, delete (if present) at le-
ast 10 Telephone numbers from the SIM-CARD
memory, and all the SMS Messages. Some
Cellphones do not organize the Telephone
Numbers in chronological order, in this case,
you must delete all the telephone numbers.

PROGRAMMING THE SIM VIA PC

This section describes the programming procedu-
re via the GS3050-A Software Application (runs
under Windows™), and provides a detailed de-
scription of all the programmable parameters.

Introduction

To access the Programming phase, proceed
as follows:
a) insert the SERV Jumper [16], or
b) trigger an Alarm on a Channel with the
'Serv' attribute (Service Channel).
If you access 'Service' mode, via the Service
Channel, the system will allow any ongoing te-
lephone call to finish, before stopping the call
cycle and activating the 'Service' mode. If the Ser-
vice Channel utilized is Channel 1, any ongoing
call will be interrupted, the call cycle stopped and
the 'Service' mode activated immediately.
During the Programming phase:
a) all the LEDs on the GS3050-A frontplate
will turn OFF;
b) 'P' will appear on the display;
c) the SMS communications and GSM Calls
will be stopped;
d) the OC Outputs will be forced to standby;
e) the GS3050-A will switch to the Land line.
A GSM-LINK cable (accessory item) is required.
The 3-pin connector must be connected to con-
nector [9], and the DB9 to the computer COM port
(refer to the 'Menu Bar' section for the Setup).

Preliminary operations

Work carefully through the following steps to
access the Programming phase:
1. Turn ON the GS3050-A and wait about 20
seconds.
2. Start the Software Application.
12
Figure 6 - Main page of GS3050-A Application
3. Connect the GSM-LINK.
4. Put the GS3050-A in 'Service' mode, as de-
scribed at the beginning of this section.
G G G G G To exit the Programming session:
disconnect the GSM-LINK and exit
'Service' mode.
The Application will open on the Main page (see
Figure 6). The Folders, Customers and Dialo-
gue windows on the left of the page (see Figu-
re 7) will allow you to program the system.
Folders: this window will allow you to ac-
cess the various Pages.
Customers: this window will allow you to
Delete or Retrieve Customers configura-
tions, as follows:
1. Using the Right button on the mouse, se-
lect the Customer.
2. Click Load to load the Customer data from
the Database to the Hard-Disk, or Delete to
delete the Customer data from the Database.
Customers can also be Loaded by double cli-
cking the Customer name.
The Customers can be listed in alphabetical or Code
order — select Name or Code as required.
Status window: this real-time window will
show Error messages, Settings, and other
information (as shown on Cellphone displays).
The Telephone, Telphone Dialler, SMS Dialler and Ou-
tputs pages will allow you to program all the system
parameters, and customize the system. The Status
and Calls pages will allow you to monitor the system.
The following sections describe all the GS3050-
A Application Pages.
T P
ELEPHONE AGE
This page (see Figure 8) will allow you to pro-
gram the Telephone numbers of the Contact per-
sons to call in the event of an Alarm (up to 8).
GS3050-A - GSM Dialler and Interface