Features; Description; Installing The Gs3050-A - DSC GS3050-A Mode D'emploi

FEATURES

GS3050-A
Simulates PSTN line
Switches to GSM Network in the event of PSTN
Trouble (Line down)
Manages and signals Incoming/Outgoing calls
7 segment status display
GSM signal strength indicator
5 programmable OC Outputs
Houses 12V-1.2Ah battery (not supplied)
Protected against tamper
Protected against PSTN over-voltage
Dual Band (900Mhz at 1800Mhz)
4 Alarm Channels
Manages 8 SMS Text Communications
Manages 8 (20 digit) telephone numbers per
channel
Control Outputs via SMS
Stop Alarm Jumper and SERVICE Channel
Optional Dialler features (with NC2/VOX)
Records up to 8 messages: 4 x 15 seconds
and 4 x 7 seconds
Voice Message can be assigned to each Alarm
Channel
Voice Message Priority (Channel 1)
4 independent Alarm channels with priority
management (Channel 1 priority)
Up to 4 call cycles
Stop Alarm Jumper (SERV)
Digital message Recording/Playback
Message playback
Plays Alarm message up to 4 times
Programmable Handshake
IMPORTANT - The SIM-CARD PIN must
be disabled before use. On power-up, the
Red LED G G G G G will turn ON for approxima-
tely 20 seconds. The Red LED will turn off
when GS3050-A is ready to operate. If the
Red LED blinks (SIM-CARD trouble), it
will be necessary to turn the device OFF
and clear the Trouble.

DESCRIPTION

The engineer-friendly GS3050-A analogue inter-
face provides total confidence in all security and
surveillance applications. It can be simply and
cost-effectively intergrated with all alarm sy-
stems, and can substitute the PSTN line comple-
tely, in zones where the GSM Service is provi-
ded, and where hardwired telephone devices
cannot be installed (mountain cabins, beach bun-
Table 1 - TECHNICAL SPECIFICATIONS
Power Supply Voltage
Max. Current draw
Operating Temperature
Dimensions (W x H x D)
Weight
(without battery)
galows, etc.).
The GS3050-A manages two-way voice and
Central station communications, and all the tele-
phone-control functions normally provided by te-
lephone diallers.
The performance of this device greatly depends on
the selected GSM Network, and signal strength.
The GS3050-A supports CONTACT ID, 10 bps,
20 bps protocols and, in areas with optimum si-
gnal strength, SIA and CESA protocols, all of
which transmit properly over the GSM Networks.
The GSM signal strength is of utmost importance,
the GS3050-A should not be located in places
where the GSM signal is weak (e.g. only one
signal strength LED ON), as communications will
be at risk.
The GS3050-A can manage up to 8 SMS Texts,
and provides a remote control feature that will al-
low Users to turn ON the 5 Outputs over the pho-
ne.
Due to the characteristics of GSM Networks, the
GS3050-A cannot be used as a modem for fax or
data transmission, or for Teleservice operations.
The GS3050-A is housed in a tamper-protected
metal casing, with built-in status display.

INSTALLING THE GS3050-A

The GS3050-A should be located in a safe dry
place, away from radio transmitters and similar
devices. When choosing the placement, remem-
ber that the GS3050-A requires a 13.8 V
min. power supply (usually from the Security sy-
stem).
The GS3050-A must be Earthed, and equipped
with standby battery (see Figure 4).
13.8 V_
1000 mA
5÷40 °C
177 x 271 x 58,5 mm
1400 g
/1 A
_
7