Table des Matières
Publicité
PIECES AILE EXTERNE
(A) Aile externe (avec aileron et tétons) ........ (G/D) 1 de chaque
(B) Pivot à boule (H=9mm) ....................................................... 2
(C) Vis 3x15mm .......................................................................... 2
(D) Chape rotule ......................................................................... 2
(E) Tringlerie aileron (filetée un bout, L=300mm) .................... 2
(F) Carénage servo aileron (plastique) .................... 1 de chaque
(G) Carénage tringlerie aileron (plastique) ................................. 2
(H) Gaine thermorétractable (60x80mm)................................... 2
PIECES AILE INTERNE
(A) Aile interne (avec volet et tétons) ............ (G/D) 1 de chaque
(B) Guignol volet (aluminium) ..................................................... 2
(C) Chape (métal) ....................................................................... 2
(D) Ecrou 2mm............................................................................ 2
(E) Tringlerie volet (filetée un bout, L=300mm) ........................ 2
(F) Carénage servo volet (CTP entoilé) ...................................... 2
(G) Carénage tringlerie volet (plastique) .................................... 2
(H) Gaine thermorétractable (60x80mm)................................... 2
PIECES AILE
(A) Clé d'aile (Ø16x500mm fibre de carbone) ........................... 1
(B) Clé d'aile (Ø10x350mm fibre de carbone) .......................... 2
(C) Piton ...................................................................................... 2
(D) Ressort ................................................................................. 1
(E) Rouleau ruban adhésif ......................................................... 1
(F) Tire-ressort ........................................................................... 1
PIECES AEROFREINS
(A) XPower ELAF 440mm (non fourni) ................................. 1 set
(B) Chapeau d'AF (440x19x3mm balsa entoilé) ........................ 2
(C) Vis à bois 3x10mm ............................................................... 6
OUTER WING PARTS
(A) Outer wing (with aileron and dowel) ............(left/right) 1each
(B) Ball pivot (H=9mm) ............................................................. 2
(C) 3x15mm screw ..................................................................... 2
(D) Ball link.................................................................................. 2
(E) Aileron pushrod (threaded one end, L=300mm) ................ 2
(F) Aileron servo cover (plastic) ....................................... 1 each
(G) Aileron pushrod cover (plastic) ............................................ 2
(H) Heat shrink tube (60x80mm) ............................................... 2
INNER WING PARTS
(A) Inner wing (with flap and dowel).................(left/right) 1 each
(B) Flap control horn (aluminium) .............................................. 2
(C) Clevis (metal) ........................................................................ 2
(D) 2mm nut ................................................................................ 2
(E) Flap pushrod (threaded one end, L=300mm) .................... 2
(F) Flap servo cover (plywood with film) .................................... 2
(G) Flap pushrod cover (plastic) ................................................. 2
(H) Heat shrink tube (60x80mm) ............................................... 2
WING PARTS
(A) Wing joiner (Ø16x500mm carbon fiber) ............................... 1
(B) Wing joiner (Ø10x350mm carbon fiber) ............................... 2
(C) Eye screw .............................................................................. 2
(D) Spring .................................................................................... 1
(E) Adhesive tape roll ................................................................. 1
(F) Spring pull tool ...................................................................... 1
SPEED BRAKE PARTS
(A) XPower ELAF 440mm (not supplied) .............................. 1 set
(B) Spoiler cover (440x19x3mm balsa with film) ....................... 2
(C) 3x10mm self tapping screw ................................................. 6
CONTENU DU KIT
PIECES MOTEUR & HELICE REPLIABLE
(A) Fuselage (avant)................................................................... 1
(B) Moteur Brushless (XC 5030/20) (non fourni) ..................... 1
(C) Vis Chc 4x12mm ................................................................... 4
(D) Platine accu (CTP 3mm) ................................................. 1 set
(E) Platine contrôleur (CTP 3mm) .............................................. 1
(F) Cône 45mm (099T1829) (non fourni) ................................. 1
(G) Pale d'hélice 18x9" (009723493) (non fourni) .................. 2
(H) Sangle Velcro® .................................................................... 1
(J)
Bande Velcro® ............................................................... 1 set
PIECES TRINGLERIE DIRECTION
(A) Fuselage (arrière) ................................................................ 1
(B) Volet de direction .................................................................. 1
(C) Charnière bâton .................................................................... 4
(D) Câble aller-retour (Ø0,5x1800mm) ...................................... 2
(E) Chape (métal) ....................................................................... 2
(F) Queue de chape (filetée) ...................................................... 2
(G) Ecrou 2,6mm ........................................................................ 2
(H) Tube Cuivre ........................................................................... 4
(I)
Guignol (aluminium) .............................................................. 2
(J)
platine servo de direction (CTP 3mm)............................ 1 set
PIECES TRINGLERIE PROFONDEUR
(A) Empennage horizontal .............................. (G/D) 1 de chaque
(B) Clé de stab (Ø8x200mm fibre de carbone) .......................... 1
(C) Clé de stab (Ø5x100mm plastique) ...................................... 1
(D) Vis à bois 2x8mm ................................................................. 1
(E) Tringlerie de profondeur (CAP Ø1,8mm filetée un bout) .......... 1
(F) Chape à rotule ................................................................ 1 set
(G) Vis 2x10mm .......................................................................... 1
(H) Ecrou 2mm............................................................................ 1
(I)
Carénage servo de profondeur (plastique) .......................... 1
(J)
Gaine thermorétractable (60x80mm)................................... 1
KIT CONTENT
MOTOR & FOLDING PROPELLER PARTS
(A) Fuselage (front) .................................................................... 1
(B) Brushless motor (XC 5030/20) (not supplied) .................... 1
(C) 4x12mm socket head screw ................................................. 4
(D) Battery mount (3mm plywood) ....................................... 1 set
(E) ESC mount (3mm plywood) .................................................. 1
(F) 45mm spinner (099T1829) (not supplied) ......................... 1
(G) 18x9" prop blade (009723493) (not supplied) .................. 2
(H) Velcro® tie ........................................................................... 1
(J)
Velcro® tape .................................................................. 1 set
RUDDER LINKAGE PARTS
(A) Fuselage (rear) ..................................................................... 1
(B) Rudder .................................................................................. 1
(C) Pin hinge ............................................................................... 4
(D) Pull-pull wire (Ø0,5x1800mm) ............................................. 2
(E) Clevis (metal) ........................................................................ 2
(F) Wire end (threaded) ............................................................. 2
(G) 2,6mm nut ............................................................................ 2
(H) Copper pipe........................................................................... 4
(I)
Control horn (aluminium)...................................................... 2
(J)
Rudder servo mount (3mm plywood) ............................. 1 set
ELEVATOR LINKAGE PARTS
(A) Horizontal stabilizer ....................................(left/right) 1 each
(B) Stabilizer joiner (Ø8x200mm carbon fiber) .......................... 1
(C) Stabilizer joiner (Ø5x100mm plastic) ................................... 1
(D) 2x8mm self tapping screw ................................................... 1
(E) Elevator pushrod (Ø1,8mm music wire, threaded one end) ..... 1
(F) Ball link............................................................................ 1 set
(G) 2x10mm screw ..................................................................... 1
(H) 2mm nut ................................................................................ 1
(I)
Elevator servo cover (plastic) .............................................. 1
(J)
Heat shrink tube (60x80mm) ............................................... 1
5
PIECES ASSEMBLAGE FUSELAGE
(A) Bâti d'assemblage (CTP 3mm) ...................................... 1 set
PIECES COCKPIT / VERRIERE
(A) Cockpit (plastique) ................................................................ 1
(B) Tête pilote (plastique) .................................................... 1 set
(C) Verrière (plastique) .............................................................. 1
(D) Renfort cockpit (avant, CTP 3mm) ....................................... 2
(E) Renfort cockpit (arrière, CTP 3mm) ..................................... 2
(F) Téton (Ø3x100mm fibre de carbone) .................................. 1
(G) Support téton (CTP 3mm) .................................................... 1
(H) Verrou de verrière .......................................................... 1 set
(I)
Support verrou de verrière (CTP 2mm) ............................... 1
(J)
CAP Ø1.8mm (filetée un bout) .............................................. 1
(K) Tube guide (Ø3x150mm plastique) ...................................... 1
AUTRES PIECES
(A) Manuel de montage .............................................................. 1
(B) Autocollants couleur ....................................................... 1 set
(C) Autocollant chapeau AF ........................................................ 1
(D) Autocollant jonction fuselage ................................................ 1
FUSELAGE JOINING PARTS
(A) Assembly jig (3mm plywood) .......................................... 1 set
COCKPIT / CANOPY PARTS
(A) Cockpit (plastic) .................................................................... 1
(B) Pilot doll head (plastic) ................................................... 1 set
(C) Canopy (plastic) .................................................................... 1
(D) Cockpit reinforcement (front, 3mm plywood) ....................... 2
(E) Cockpit reinforcement (rear, 3mm plywood) ........................ 2
(F) Dowel (Ø3x100mm carbon rod) ........................................... 1
(G) Dowel mount (3mm plywood) ............................................... 1
(H) Canopy latch.................................................................... 1 set
(I)
Canopy latch mount (2mm plywood) .................................... 1
(J)
Ø1.8mm music wire, threaded one end) .............................. 1
(K) Guide pipe (Ø3x150mm plastic) ........................................... 1
OTHER PARTS
(A) Construction guide book ....................................................... 1
(B) Color sticker .................................................................... 1 set
(C) Speedbrake top cover sticker ............................................... 1
(D) Fuselage joining tape ............................................................ 1
Publicité
Table des Matières
