Publicité

Liens rapides

Notice de montage et d'utilisation
Planeur électrique de performance
Caractéristiques techniques / Technical data :
Envergure / wingspan : 2,60 m
Longueur / length :
1,23 m
Poids / TO weight :
1,8 / 2,0 kg
Surface / wing area :
47,8 dm
Profil / airfoil :
Spécial
Equipements recommandés / Related items :
Moteur / motor :
XPower F3820/10 (#099F382010)
Contrôleur / ESC :
XPower XREG40 (# 099REG40)
Accu de propulsion / Power pack :
Hélice / Propeller :
XPower
Cône/Spinner :
XPower
Radio / RC set :
Récepteur/receiver : JETI DUPLEX R9 EX
Ailerons
Profondeur/elevator : 1 servo TOPMODEL MS2810MG (#0200S2810MG)
Direction/rudder:
Volets/Flaps:
ATTENTION !
Ce modèle à construire n'est pas un jouet, il
ne convient pas aux enfants de moins de
14 ans.
Une mauvaise utilisation de ce matériel peut
provoquer des dommages matériels
ou corporels. Vous êtes pleinement
responsable
lorsque vous utilisez votre modèle.
Volez à une distance de sécurité des zones
habitées.
Soyez sûr que personne n'émet sur la même
fréquence que vous.
Order N°
2
XPower Xtreme 60C 11,1 V 2600 mAh
12 x 6" #099FB1206
Turbo XPower Ø41/Ø5 mm (#099T1811)
Orange
2 servos TOPMODEL MS2810MG (#0200S2810MG)
pantone 151c
1 servo TOPMODEL MS2810MG (#0200S2810MG)
2 servos TOPMODEL MS2810MG (#0200S2810MG)
CAUTION !
This model construction kit is not a toy and is
not suitable for children under the age of 14.
Incorrect use of this material could cause
material damage ou personal injury.
You are fully responsible for your actions
when you use this model.
Fly at a safe distance from occupied zones.
Be sure that no one else is using the same
frequency as you.
099007
High performance
Distribué par / Distributed by:
TOPMODEL
S.A.S.
Le jardin d'entreprises de SOLOGNE - F-41300 SELLES SAINT DENIS
www.topmodel.fr
electro-glider
Pour modélistes ayant
un bon niveau
ADV
For advanced
modellers
ARF
©TOPMODEL 2015
With
With
With

Publicité

Table des Matières
loading

Sommaire des Matières pour XPower BENKA 2,60M

  • Page 1 XPower F3820/10 (#099F382010) For advanced Contrôleur / ESC : XPower XREG40 (# 099REG40) modellers Accu de propulsion / Power pack : XPower Xtreme 60C 11,1 V 2600 mAh Hélice / Propeller : XPower 12 x 6” #099FB1206 With Cône/Spinner : XPower Turbo XPower Ø41/Ø5 mm (#099T1811)
  • Page 2: Important

    Sécurité d’abord ! Nous vous remercions pour votre attention lors de l’assemblage de nos kits, et vous souhaitons de bons et nombreux vols ! TOPMODEL SAS Notice XPower - Page 2 - Benka...
  • Page 3 For this, please, check all glue joints and assemblies. Safety first ! We thank you for your attention during the assembly of our kits, and wish you good and numerous flights ! TOPMODEL SAS Notice XPower - Page 3 - Benka...
  • Page 4: Retendre L'entoilage

    This may cause the trim colors to over shrink and pull away leaving sightly gaps on the color lines. The trim stripes are especially vulnerable to over shrinking. Notice XPower - Page 4 - Benka...
  • Page 5 (E4) Clé de stab arrière Ø 2 mm x 100 mm ......1 (E4) Aft stab joiner Ø 2 mm x 100 mm ........1 DIVERS MISC (D) Planche d'autocollants .............1 (D) Decals ..................1 set Notice XPower - Page 5 - Benka...
  • Page 6: A Rajouter Pour Assembler Ce Kit To Be Added To Build This Kit

    - 1 contrôleur brushless XPower XReg 40 (# 099REG40) - 1 ESC XPower XReg 40 (# 099REG40) - 1 Pack Lipo 3S 2600 mAh XPower XTreme (# 09926003S1P) - 1 Lipo Pack 3S 2600 mAh XPower XTreme (# 09926003S1P) - 1 XPower FOLDING PROP 12 x 6 (#099FB1206) - 1 XPower FOLDING PROP 12 x 6 (#099FB1206) - 1 Cône XPower Turbo Ø41/Ø5 mm (#099T1811)
  • Page 7: Montage De L'aile Gauche Left Wing Assembly

    Connect the servo (be sure to respect polarity). Slide the heatshrink tube over the connector and retract it with a hot air gun or a lighter. Notice XPower - Page 7 - Benka...
  • Page 8 Using a thin steel wire (non included), route the servo extensions into the wing and make the connectors exit from the hole at the root rib. Notice XPower - Page 8 - Benka...
  • Page 9 Remove the clevis. Make a Z bend on the mark. Cut the pushrod 5 mm after the bend. Insert the Z bend in the servo arm. Set the clevis to have aileron centered when servo is centered. Connect the clevis to the aileron horn. Notice XPower - Page 9 - Benka...
  • Page 10 14) Découpez et collez le cache de servo de volet ainsi que le cache de sortie de commande côté extrados. Cutout and secure the flap servo cover and the pushrod cover at the top of the wing. Notice XPower - Page 10 - Benka...
  • Page 11: Montage De L'aile Droite Right Wing Assembly

    4) Appliquez un peu d'époxy dans le trou et sur les filets du guignol et vissez le guignol dans le trou. Apply a small drop of epoxy into the hole and to the threads of the brass horn. Screw in the horn into the hole. Notice XPower - Page 11 - Benka...
  • Page 12 Using medium CA or epoxy, attach the 3 parts of the servo tray together as shown. Test fit (don't glue) the servo tray into the fuse. Draw a mark on each outer tube 10 mm behind the servos opening. Notice XPower - Page 12 - Benka...
  • Page 13 Cut the wires 5 mm after the Z bend. Insert the servo arms on the Z bends, and fit the servo arms on the servos head (the servos are centered with your radio system). Notice XPower - Page 13 - Benka...
  • Page 14 6) Fixez le porte pale sur l'axe du moteur et le cône sur le porte pales. Secure the prop holder on the motor axle, and the spinner to the blade holder. Notice XPower - Page 14 - Benka...
  • Page 15 Slide the stabs on the wires. If needed, make a slight bend at the ends of the main wire, so that the stabs stay firm on the wires. Notice XPower - Page 15 - Benka...
  • Page 16 12) Prenez le temps d'admirer votre Benka ! To fit the canopy, slide the front wire, push the canopy Take a moment to admire your Benka ! forward, then slide the rear wire. Notice XPower - Page 16 - Benka...
  • Page 17: Centrage - Cg Location

    5 mm à piquer / 38 mm 5 mm Down Note : Les débattements sont mesurés au plus large de chaque gouverne. Note : Throws are measured at the widest part of each surface. Notice XPower - Page 17 - Benka...
  • Page 18 Portée : Faire un essai de portée sans et avec le moteur en fonctionnement, en accord avec les instructions du fabricant de la radio. Si la portée est insuffisante ou si elle est réduite avec le moteur tournant, ne jamais voler avant d’avoir complètement résolu le problème ! Notice XPower - Page 18 - Benka...
  • Page 19 à la section Bons vols… DOC-NOTICE. Good flights… Internet construction guide in color ! : The manual is downloadable on our website on the product page, section DOCUMENTATION. Notice XPower - Page 19 - Benka...
  • Page 20 NOTES Notice XPower - Page 20 - Benka...

Ce manuel est également adapté pour:

099007

Table des Matières