Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
FR
EN DE
ES
EN
FR
DE
ES
DE
FR
EN
ES
ES
FR
EN
DE
be able to separate from intermediate pole once
assembled correctly. Repeat above steps if poles can
IT
FR
EN
DE
ES
be separated from intermediate pole.
FR
EN
DE
ES
IT
WaRNINg
FR
EN
DE
ES
IT
Failure to lock powerhead pole as directed above
could result in serious injury or death.
FR
EN
DE
ES
IT
OPERTION
FR
EN
DE
ES
IT
FR
EN
DE
ES
IT
WaRNINg:
Do not allow familiarity with this product to make
FR
EN
DE
ES
IT
you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
FR
EN
DE
ES
IT
FR
EN
DE
ES
IT
WaRNINg:
Always wear safety goggles or safety glasses
FR
EN
DE
ES
IT
with side shields when operating power tools.
Failure to do so could result in objects being
FR
EN
DE
ES
IT
thrown into your eyes, resulting in possible serious
injury.
FR
EN
DE
ES
IT
FR
EN
WaRNINg:
DE
ES
IT
Do not use any attachments or accessories not
FR
EN
DE
ES
IT
recommended by the manufacturer of this product.
The use of attachments or accessories not
FR
EN
DE
ES
IT
recommended can result in serious personal
injury.
FR
EN
DE
ES
IT
aPPLICaTIONS
FR
EN
DE
ES
IT
You may use this product for the purposes listed below:
FR
EN
DE
ES
IT
Limbing
Pruning
FR
EN
DE
ES
IT
aDDINg BaR aND CHaIN LUBRICaNT
See Figure 3
Use Ryobi Bar and Chain Lubricant. It is designed for
chains and chain oilers, and is formulated to perform over
a wide temperature range with no dilution required.
NOTE: Pole saw comes from the factory with no bar and
chain oil added. Level should also be checked after every
20 minutes of use and refilled as needed.
Remove oil cap.
Carefully pour the bar and chain oil into the tank.
Wipe off excess oil.
Check and fill the oil tank when quick view oil
indicator is below the second to last indicator line.
Repeat as needed.
NOTE: It is normal for oil to seep from the saw when not
IT
PT
NL
SV
DA
IT
PT
NL
SV
DA
English(original instructions)
IT
PT
NL
SV
DA
IT
PT
NL
SV
DA
PT
NL
SV
DA
PT
NL
SV
DA
NL
PT
SV
DA
SV
PT
NL
DA
DA
PT
NL
SV
NO
PT
NL
SV
DA
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
NO
FI
HU CS RU
NO
FI
HU CS RU
NO
FI
HU CS RU
NO
FI
HU CS RU
in use. To prevent seepage, empty the oil tank after each
use then run for one minute. When storing the unit for a
NO
FI
HU CS RU
long period of time (three months or longer) be sure the
chain is lightly lubricated; this will prevent rust on the
NO
FI
HU CS RU
chain and bar sprocket.
NO
FI
HU CS RU
CONNECTINg TO POWER SUPPLY
NO
FI
HU CS RU
See Figure 4
NO
FI
HU CS RU
This product is designed with a cord retainer that
prevents the extension cord from being pulled loose while
FI
HU CS RU
using.
Form a loop with the end of the extension cord.
FI
HU CS RU
Insert loop portion of extension cord through opening
HU
in the bottom of the rear handle and place over cord
FI
CS RU
retainer.
CS
FI
HU
RU
Slowly pull loop against cord retainer until the slack is
removed.
RU
FI
HU CS
Plug product into extension cord.
NOTE: Failure to remove all excess cord slack from
FI
HU CS
RU
extension cord retainer could result in plug loosening
FI
HU CS
RU RO
from receptacle.
FI
HU CS
RU RO
STaRTINg aND STOPPINg
See Figure 4
FI
HU CS
RU RO
To start the motor:
FI
HU CS
RU RO
Connect the pole saw to power supply.
Place your thumb on the lock-off button and pull it
FI
HU CS
RU RO
completely towards you.
FI
HU CS
Fully depress the switch trigger.
RU RO
FI
HU CS
RU RO
To stop the motor:
Release the switch trigger.
FI
HU CS
RU RO
aDJUSTINg TELESCOPIC POLE
See Figure 5.
Disconnect the pole saw from the power supply.
Rotate the collar counterclockwise to loosen.
Push poles towards each other to shorten the pole or
pull away from each other to lengthen the pole.
NOTE: Extend the pole only to the length required to
reach the limb being cut. Do not extend the handle
above waist height.
When the desired length is achieved, rotate the collar
clockwise to secure.
NOTE: Adjust hand placement on the shaft of the
pole saw to keep proper balance. Do not attempt to
use the pole saw at a length which does not allow
you to achieve proper footing and balance at all
times.
12
RO PL
SL
HR ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO
PL
SL
HR
ET
PL
SL
HR
ET
SL
PL
HR
ET
HR
PL
SL
ET
ET
PL
SL
HR
PL
SL
HR
ET
PL
SL
HR
ET
PL
SL
HR
ET
PL
SL
HR
ET
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LV
LT
SK BG
SK
LT
LV
BG
BG
LT
LV
SK
Publicité
Table des Matières
