Maintenance And Cleaning; Technical Data - Renkforce 1218438 Mode D'emploi

6. Make a small hole in the rubber gasket of the cable inlet.
7. Push the stripped mains cable through the rubber gasket and the strain relief in the
junction box from underneath.
8. Connect the 3 wires on the mains cable to the 3-pole screw terminal (brown = L/
phase, blue = N/neutral wire, yellow-green = PE/earth wire/earth symbol).
9. Also check the other screw connections on the screw terminal (for the connection
cables to the LED driver) and tighten them if necessary.
10. Place the screw terminal back on the retaining pins.
11. Replace the cover of the junction box by tightening all four screws.
12. Place the junction box back in the floor stand of the lamp. Be careful not to kink the
cable or damage it in any other way.
13. Now secure the lamp to the floor stand at a suitable location on the ground with
three screws and, if necessary, dowels. Depending on the surface, suitable
screws and dowels are required.
Ensure that no existing cables or pipes (also water pipes) are damaged
when drilling mounting holes or securing screws.
Ensure that the floor lamp is positioned vertically. If necessary, use a spirit
level to check that the lamp is positioned vertically.
It is recommended to install a switch to turn the floor lamp on/off.

Maintenance and cleaning

• Never point a garden hose or a pressure washer at the LED outdoor floor lamp!
• You do not need to carry out maintenance work on the product. Leave maintenance
or repair work to an expert. The light bulbs are firmly embedded and cannot be
changed.
• Turn off the mains voltage for the floor lamp before cleaning; let the lamp cool down
sufficiently.
• You can use a clean, soft and dry cloth to clean the lamp. Dust can be easily removed
using a clean and soft brush and a vacuum cleaner.
• Do not use any aggressive, chemical or abrasive detergents as these can result in
discolourations or even changes to the surface material.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the
relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of
the environment.

Technical Data

a) Item no. 1218438
Operating voltage................................220 - 240 V/AC, 50 Hz
Protection type ....................................IP44
Protection class ..................................I
Material ................................................Stainless steel V2A
Mounting location ...............................Indoors/outdoors
Power consumption............................max. 10.5 W
Illuminant ..............................................60 LEDs (embedded, not replaceable)
Colour temperature.............................2700 - 3000 K (warm-white)
Luminous flux .......................................690 lm
Operating conditions ..........................-40 to +55 °C, 0 - 95 % RH
Storage conditions..............................-25 to +65 °C, 0 - 95 % RH
Dimensions (Ø x H)..............................120 x 440 mm
Weight ...................................................approx. 700 g
b) Item no. 1218440
Operating voltage................................220 - 240 V/AC, 50 Hz
Protection type ....................................IP44
Protection class ..................................I
Material ................................................Stainless steel V2A
Mounting location ...............................Indoors/outdoors
Power consumption............................max. 10.5 W
Illuminant ..............................................60 LEDs (embedded, not replaceable)
Colour temperature.............................2700 - 3000 K (warm-white)
Luminous flux .......................................690 lm
Operating conditions ..........................-40 to +55 °C, 0 - 95 % RH
Storage conditions..............................-25 to +65 °C, 0 - 95 % RH
Dimensions (Ø x H)..............................120 x 760 mm
Weight ...................................................approx. 880 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the
technical status at the time of printing.
© Copyright 2014 by Conrad Electronic SE. V1_1014_02-DS