Adjusting The Cutting Depth; Adjusting The Cutting Angle; Changing The Saw Blade; Adjusting The Riving Knife - Festool TS 75 EBQ Notice D'utilisation D'origine

6.1 Electronics
The machine (TS 75 EBQ, TS 75 EQ) comes with
full-wave electronics with the following proper­
ties:
Smooth start-up
The electronically controlled smooth start-up
function ensures that the power tool starts up
smoothly.
Constant speed
The motor speed is electronically kept con­
stant. This ensures a uniform cutting speed
even when under load.
Speed control
You can continuously adjust the speed within
the speed range using the adjusting wheel [1-5]
(see Technical data). This enables you to opti­
mise the cutting speed to suit specific surfaces
(see Section ).
Temperature cut-out
When exceeding a certain engine temperature
level, the machine power supply and speed are
capped. The power tool continues operating at
reduced power to allow the ventilator to cool
the motor rapidly. The power tool resumes to
full performance automatically once the motor
has cooled sufficiently.
Current limiting
Current limiting prevents excessive current
consumption under extreme overload, which
can lead to a decrease in the motor speed. The
motor immediately restarts after the load is re­
moved.
Brake
The TS 75 EBQ comes with an electronic brake.
The saw blade is stopped electronically within
approximately two seconds of switching off the
machine.
6.2

Adjusting the cutting depth

The cutting depth can be set at 0–75 mm at the
cutting depth stop.
► Push down on the cutting depth stop [3-3]
and move it to the required cutting depth
(the values specified on the scale [3-1] ap­
ply to 0° cuts without a guide rail),
► Release the cutting depth stop (the cutting
depth stop clicks into pace at 1 mm incre­
ments).
The saw unit can now be pushed downwards as
far as the cutting depth that is set.
A threaded pin (M4x8 up to M4x12)
can be screwed into the hole [3-2] in
the cutting depth stop. By turning the
threaded pin, the cutting depth can be
adjusted even more precisely (+/-
0.1 mm).
6.3

Adjusting the cutting angle

The saw unit can be swivelled between 0° and
47°:
► Open the rotary knobs [3-4, 3-6].
► Swivel the saw unit to the desired cutting
angle [3-5].
► Retighten the rotary knobs.
The two end positions are set at the
plant to 0° and 45°. By turning the two
threaded pins [3-7] in an anti-clock­
wise direction, the end position can be
increased from 45° to a maximum of
47°.
6.4

Changing the saw blade

CAUTION
Risk of injury from hot and sharp tool
► Do not use any blunt or faulty tools.
► Wear protective gloves.
► Turn the lever [4-2] as far as the stop,
► Slide the safety lock [4-1] up and push the
saw unit down until it locks into place,
► Loosen the screw [4-4] using the hex
key [4-3],
► Remove the saw blade,
► Clean the flange [4-8, 4-10],
► Insert the new saw blade.
The direction of rotation of the saw
blade [4-9] and machine [4-7] must match!
► Insert the outer flange [4-10]so that the pin
engages in the recesses on the inner
flange [4-8],
► Tighten the screw [4-4],
► Reposition the lever [4-2].
6.5

Adjusting the riving knife

► Turn the lever [4-2] as far as the stop,
► Slide the safety lock [4-1] up and push the
saw unit down until it locks into place,
► Loosen the screw [4-6] using the hex
key [4-3],
► Adjust the riving knife according to the dia­
gram [4]
► Tighten the screw [4-6],
► Reposition the lever [4-2].
English
19