Led Indicators; Supported Vehicle Interfaces; Getting Started; Installing The Vci Manager Software - Bosch MTS 6516 VCI Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 32
4.10.3

LED Indicators

Four Light Emitting Diodes (LEDs), are located on the
front of the MTS 6516 VCI. The LED indicators provide
the following status information.
LED Symbol
LED Function
Vehicle Communication
Error Indicator
PC Host Communication
Power On
4.11

Supported Vehicle Interfaces

The following sections list the vehicle communication
interfaces supported by the MTS 6516 VCI.
4.11.1
Serial Data Interfaces
The MTS 6516 VCI supports the following Serial Data
Interfaces.
R
Three Independent CAN Controllers (ISO 11898-1)
R
Three Two-Wire (High-Speed) CAN Transceivers (ISO
11898-2)
R
Low-Speed, Fault-Tolerant CAN transceiver (ISO 11
898-3)
R
Single-Wire CAN Transceiver (J2411)
R
Two Independent K-Line Interfaces (software selec-
table pins)
R
L -Line Interface
R
GM 5V UART (J2740)
R
J1708
R
SAE J1850 VPW
R
SAE J1850 PWM
R
Ford UBP
R
Chrysler SCI (5V)
R
Chrysler CCD
R
Nissan DDL1
4.11.2
Non-Serial Data Interfaces
The MTS 6516 VCI supports the following Non-Serial
Data Interfaces.
R
14 Analog Input Signals (all 13 DLC signal pins plus
battery pin)
R
13 Discrete Output Signals (Open Drain, Vbat, or
5V)
R
13 Discrete Input Signals (software controlled
threshold)
R
Programming Voltage Output (5V to 20V switchable
to 6 pins)
R
Crank Detect Circuit
Robert Bosch GmbH
5.

Getting Started

The following sections provide the information needed
to begin using the MTS 6516 VCI including installing the
VCI Manager software, updating the firmware on the
device, configuring connection methods, and communi-
cating with the vehicle.
5.1

Installing the VCI Manager Software

The VCI Manager software is installed on the PC and
provides access to the VCIs located on your network.
The VCI Manager must be installed on the PC in order
to configure, update and run diagnostic applications
targeted for the PC. Initially you use the VCI Manager
software to set up the configuration of each VCI. The
VCI Manager is also used to update the firmware on the
VCI. MTS 6520 Software updates are available from the
Bosch Diagnostics OES website. Use the following pro-
cedure to install the VCI Manager software on your PC.
1. Visit the Bosch Diagnostics OES website at the
following address to determine if a newer version of
VCI Manager software is available for your device. If
the software on the website is newer than that inclu-
ded on the Installation CD, download the software
to your computer.
http://www.diagnostics-oes.de/diagnostics_oes/en/ser-
vice/downloads.htm
2. If you downloaded the software from the website,
double-click the downloaded file and follow the
instructions on the screen. Otherwise, Place the VCI
Software Installation CD into your CD drive. [The CD
should auto run and launch the VCI Manager instal-
lation program. If the CD does not auto run, double-
click setup.exe on the root directory of the CD to
start the installation.] The InstallShield Wizard starts
and guides you through the software installation
3. The InstallShield wizard displays a panel indicating
that the program is ready to be installed. Click Ins-
tall to proceed with the installation. A progress bar
shows the status of the installation. [You can click
Cancel if you want to halt the installation process.
| MTS 6516 VCI | 23
en
|
1699200075 B
2017-06-20

Publicité

Table des Matières
loading

Table des Matières