Publicité
Les langues disponibles
Les langues disponibles
Cleaning wall surfaces
1. Attach the T-Racer directly to the high-pressure gun.
a Press the bayonet connector of the T-Racer into
the connection on the high-pressure gun and
then turn by 90° until it latches into place.
b Tighten the union nut if present.
2. Clean the wall surface.
Rotor arm height adjustment
The clearance of the high-pressure nozzles to the sur-
face to be cleaned can be adjusted via the rotor arm
height adjustment.
Adjust the rotor arm height adjustment. according to the
surface to be cleaned.
Illustration D
For powerful cleaning of stubborn soiling on dura-
ble surfaces, e.g. tiles, concrete, stone:
1. Set the rotor arm height adjustment to "HARD".
For cleaning sensitive surfaces:
2. Set the rotor arm height adjustment to "SOFT".
Surface cleaning foot switch
For cleaning larger areas:
1. Press the surface cleaning foot switch.
A water jet is emitted from the two high-pressure
nozzles in the rotor arm.
Edge and corner cleaning foot switch
Note
Guide the T-Racer along the corner area to achieve op-
timum cleaning results.
For cleaning corners and edges:
1. Press the edge and corner cleaning foot switch.
A water jet is emitted from the front high-pressure
nozzle.
Rinsing function foot switch
Note
The device has a rinsing function for pre-wetting or rins-
ing the cleaned surface.
For rinsing:
1. Press the rinsing function foot switch.
A strong jet, but not a high-pressure water jet is
emitted from the rinsing nozzle.
After use
Rinse off the device with a gentle water stream after
use.
Detach the T-Racer and any extension tubes from
the high-pressure gun.
Rinse off the T-Racer with the high-pressure gun
(without accessories) or wipe down with a damp
cloth.
Storage
Store the device in a frost-protected place.
Care and service
Removing/installing the nozzles
The described procedure applies to all nozzles on the
device.
Illustration E
1. Remove the clip.
2. Pull the high-pressure nozzle out.
3. Fit the high-pressure nozzle.
4. Fit the clip.
Cleaning the high-pressure nozzle
1. Remove the high-pressure nozzle.
8
2. Flush the high-pressure nozzle with clear water in
both directions. Replace a damaged high-pressure
nozzle where necessary.
3. Install the high-pressure nozzle.
Replacing the skids
Worn or damaged skids can be easily replaced:
Illustration F
1. Press the skid gently upwards and out of the latch
using a suitable tool such as a screwdriver.
2. Pull the skid upwards and out.
3. Press the new skid gently into the support until it
latches into place.
Troubleshooting guide
High-pressure cleaner not building up pressure or
pulsing
High-pressure nozzles clogged or damaged.
1. Remove the high-pressure nozzles.
2. Check the high-pressure nozzles for clogging and
clean if necessary.
3. Check the high-pressure nozzles for damage and
replace if necessary.
4. Flush the T-Race with clear water without the noz-
zles fitted.
5. Install the high-pressure nozzles.
Incorrect high-pressure nozzle selected.
The device only provides optimum cleaning results
when used with the appropriate high-pressure nozzles!
1. Select the appropriate high-pressure nozzles ac-
cording to the high-pressure cleaner used.
2. Install the high-pressure nozzles.
The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)
Remarques générales..........................................
lisation ..................................................................
Utilisation conforme..............................................
Protection de l'environnement..............................
Accessoires et pièces de rechange .....................
Etendue de livraison.............................................
Consignes de sécurité..........................................
Symboles sur l'appareil ........................................
Description de l'appareil .......................................
Montage du tuyau de rallonge..............................
Mise en service ....................................................
manuel .................................................................
Après l'utilisation ..................................................
Stockage ..............................................................
Entretien et maintenance .....................................
Dépannage en cas de défaut ...............................
Garantie ...............................................................
Français
Warranty
Contenu
9
9
9
9
9
9
9
10
10
10
10
10
11
11
11
11
11
Publicité
Chapitres
Dépannage
