Internal Display; Measurement - Nikon ACULON Manuel D'utilisation

Internal display

En
Es
Fr
Distance
Pt
Laser irradiation mark
Battery condition
『 』 - Aim at the target you want to measure. Position the target at the center of the target mark.
『 』 - Appears while the laser is being irradiated for a measurement.
Remains present during single measurement. Blinks during continuous measurements.
Do not look into the objective lens while this mark is shown.
『 』 - Now measuring
『 』 - "Failure to measure" or "Unable to measure"
* Usually, an LCD employs equal or lower magnification. However the LCD of this product is magnified
by the high magnification of the eyepiece. Although this LCD was produced using the most advanced
technology, it is impossible to eliminate dust completely. As a result, dust may be seen. It will not,
however, affect measurement accuracy or safety during use.
12
Unit of measure (m/yd.)
Target mark

Measurement

Caution — use of controls or adjustments or
performance of procedures other than those
specified herein may result in hazardous radiation
exposure.
1. Install a battery in the battery chamber. (See
"Inserting and Changing Battery")
2. Diopter adjustment
Adjust diopter to obtain a clear image in the LCD.
First, rotate the diopter adjustment ring
counterclockwise until it comes to a complete stop.
Next, turn on the power to activate the LCD when
you look through the Nikon Laser Rangefinder.
Rotate the diopter adjustment ring clockwise until
the display comes into focus.
If the diopter is not adjusted to correspond to your
eyesight, you may not be able to correctly aim at
your subject.
3. Measuring
Before measuring, be sure to confirm unit setting.
Measurement
Measurement 1. Turn on the power (Confirm Measurement
2. Aim at the target.
the internal display is on).
Position the target at
1. Press the POWER button for power-on. 1. Press the POWER button for power-on.
1. Press the POWER button for power-on. 2. Aim at the target.
2. Aim at the target.
(Automatic power shut-off after
(Power turns off 8 seconds after the last
(Power turns off 8 seconds after the last (Power turns off 8 seconds after the last
the center of the reticle.
approx. 8 sec. unattended.)
operation.)
operation.) operation.)
Immediately Stand-by. Target aiming.
Immediately after power-on. Stand-by. Target focusing.
Immediately after power-on. Immediately after power-on. Stand-by. Stand-by. Target focusing.
after power-on.
(Initializing)
(Initializing) (Initializing)
(Initializing)
3. Press POWER button once to start
3. Press POWER button once to start 3. Press POWER button once to start
continuous measurement for 8 seconds.
continuous measurement for 8 seconds. continuous measurement for 8 seconds.
(Initializing)
Immediately after power-on. Stand-by.
(Initializing) (Initializing) (Initializing)
(Initializing)
3. Press POWER button once to start
3. Press POWER button once to start 3. Press POWER button once to start 3. Press POWER button once to start
continuous measurement for 8 seconds.
3. Press POWER button once to start
continuous measurement for 8 seconds. continuous measurement for 8 seconds.
continuous measurement for 8 seconds.
(Single measurement mode is not 3. Press POWER ON/Measurement button once to start measurement.
continuous measurement for 8 seconds.
(Single measurement mode is not (Single measurement mode is not
(Single measurement mode is not
available with this laser rangefinder.)
Keeping the button depressed enables continous measurement up
(Single measurement mode is not
available with this laser rangefinder.) available with this laser rangefinder.) available with this laser rangefinder.)
available with this laser rangefinder.) to approx. 20 seconds.
Measuring.
Measuring. Measuring. Measuring.
Measuring.
Measuring.
4. For 8 seconds, the internal display shows "distance" and "fail to measure" indicator alternately.
4. During measurement, the internal display shows "distance" and "fail
4. For 8 seconds, the internal display shows "distance" and "fail to measure" indicator alternately. 4. For 8 seconds, the internal display shows "distance" and "fail to measure" indicator alternately.
4. For 8 seconds, the internal display shows "distance" and "fail to measure" indicator alternately.
(Laser irradiation mark is blinking.)
4. For 8 seconds, the internal display shows "distance" and "fail to measure" indicator alternately. to measure" indicator alternately. (Laser irradiation mark is blinking.)
(Laser irradiation mark is blinking.) (Laser irradiation mark is blinking.) (Laser irradiation mark is blinking.)
(Laser irradiation mark is blinking.)
Failure to measure or Displays the
Failure to measure or Displays the measured
unable to measure Failure to measure or Failure to measure or Failure to measure or Displays the measured measured figure. Displays the measured Displays the measured
figure. (Target 1)
unable to measure distance.
Displays the measured
Failure to measure or figure. (Target 1) figure. (Target 1)
unable to measure distance. unable to measure distance. unable to measure distance. figure. (Target 1)
distance. (Target 1)
figure. (Target 1)
unable to measure distance.
5. After measurement, the measured results are displayed for
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
2. Aim at the target. 5. After continuous measurement, the measured results are displayed for 8 seconds, then power 5. After continuous measurement, the measured results are displayed for 8 seconds, then power 5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
approx. 8 seconds, then power turns off. If you press the POWER
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off. turns off. turns off.
If you press the POWER button during power-on (while the internal display is lit), another
turns off. ON/Measurement button during power-on (while the internal
If you press the POWER button during power-on (while the internal display is lit), another If you press the POWER button during power-on (while the internal display is lit), another If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts. 8-second measurement starts. display is active), another measurement starts. 8-second measurement starts.
8-second measurement starts.
Target focusing.
Target focusing.
En
Es
Fr
Pt
Displays the
Displays the measured
Displays the measured Displays the measured measured figure. Displays the measured
figure. (Target 2)
Displays the measured
figure. (Target 2) figure. (Target 2)
figure. (Target 2)
(Target 2)
figure. (Target 2)
13