Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
IMPORTANT INFORMATION
At any time and without prior notice Ayce Power tool reserves the right to change and
improve the design and the technical specifications of this product.
INTENDED USE
This machine is designed for drilling in wood and metal sheets, screwing. Do not use
machine attachments for works other than those for which they are designed for!
SPECIAL SAFETY INSTRUCTIONS
1.Wear ear protectors. Exposure to noise can cause hearing loss.
2.Hold power tool by insulated gripping surfaces, when performing an operation where
the cutting accessory may contact hidden wiring. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power tool "live" and could give the operator
an electric shock.
3.Hold power tool by insulated gripping surfaces, when performing an operation where
the fastener may contact hidden wiring. Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give the operator an electric
shock.
4.If possible, always use clamps or a vice to hold your work.
5.Always switch off before you put the tool down.
6.Ensure that the lighting is adequate.
7.Do not put pressure on the tool, such that it slows the motor down. Allow the bit to
screw without pressure. You will get better results and you will be taking better care of
your tool.
9.Only use accessory bits in good condition.
10.Before starting, check that there is sufficient clearance for the bit under the work-piece.
11.Do not touch the bit after operation. It will be very hot.
12.Keep your hands away from under the work-piece.
13.Never use your hands to remove dust, chips or waste close by the bit.
14.Rags, cloths, cord, string and the like should never be left around the work area.
15.Support the work properly.
16.16.If you are interrupted when operating the tool, complete the process
and switch off before looking up.
17.Periodically check that all nuts, bolts and other fixings are properly tightened.
18.When using the tool, use safety equipment including safety glasses or shield,
hearing protection, and protective clothing including safety gloves. Wear a dust mask
if the operation creates dust.
19.Even when the tool is used as prescribed it is not possible to eliminate all residual
Damage to the lungs if an effective dust mask is not worn.
Damage to hearing if effective hearing protection is not worn.
20. The machine shall be used in a covered and dry area. The ambient temperature
shall be included between 15°C and 30°C. The humidity level shall be less than 60%.
EXTRA SAFETY REGULATIONS CONCERNING BATTERY
To ensure the longest battery life and best battery performance, always charge the
•
battery when the temperature is between 18-24°C. Do not charge the battery pack
when the temperature is below 0°C, or above 40°C. This is important. Failure to
observe this safety rule could cause serious damage to the battery pack.
•
Do not incinerate the battery pack even if it is seriously damaged or can no longer
hold a charge. The battery pack can explode in a fire.
•
A small leakage of liquid from the battery pack may occur under extreme usage or
temperature. This does not necessarily indicate a failure of the battery pack. However,
Wash the affected area quickly with soap and water.
Neutralise the liquid with a mild acid such as lemon juice or vinegar.
Flush your eyes with clean water for a minimum of 10 minutes and seek immediate
medical attention. Inform the medical staff that the liquid is a 25-35% solution of
potassium hydroxide.
•
Never attempt to open the battery pack for any reason. If the plastic housing of the
battery pack breaks open or cracks, immediately discontinue its use and do not
recharge it.
•
Do not store or carry a spare battery pack in a pocket or toolbox or any other place
where it may come into contact with metal objects. The battery pack may be short
circuited causing damage to the battery pack, burns or a fire. If storing or disposing
the battery pack, cover the terminals with a heavy insulation tape to ensure short
circuit cannot occur. Batteries, when stored for a long period of time, will discharge.
•
Do not store or use the tool and battery pack in locations where the temperature may
reach or exceed 40°C such as alongside sheds or metal structures in the summer.
•
Allow the battery pack to cool down after charging. Do not place it in a hot environment
such as a metal shed or open trailer left in the sun.
•
Only charge the battery with the charger supplied.
Do not put the battery pack near fire or high temperature position.
•
Do not splash or immerse in water or other liquids. This may cause premature cell
•
failure.
76 |
77
GB
GB
Publicité
Table des Matières
