Instructions For The Electrical Connection - Gaggenau AC250121 Notice D'utilisation Et De Montage

en Installation instructions
Use only suitable tools and equipment.
▶
The appliance is heavy.
¡
The appliance must not be fitted directly onto
▶
plasterboard or similar lightweight materials.
To ensure correct installation, you must use a
▶
material which is sufficiently stable and suitable
for both the structural conditions and the weight
of the appliance.
Changes to the electrical or mechanical assembly
¡
are dangerous and may lead to malfunctions.
Do not make any changes to the electrical or
▶
mechanical assembly.
Risk of falling when working on the appliance
¡
Use a stable stepladder.
▶
Do not lean over the hob.
▶
Do not step on the hob or the work surface.
▶
The filter cover may swing out.
¡
Open the filter cover slowly.
▶
Take hold of the filter cover after opening until it
▶
no longer swings out.
Close the filter cover slowly.
▶
Risk of injury when opening and closing the hinges.
¡
Keep your hands away from the hinges.
▶
WARNING ‒ Risk of electric shock!
Sharp-edged components inside the appliance may
¡
damage the connecting cable.
Do not kink or trap the connecting cable.
▶
If the appliance or the power cord is damaged, this
¡
is dangerous.
Never operate a damaged appliance.
▶
Never pull on the power cord to unplug the appli-
▶
ance. Always unplug the appliance at the mains.
If the appliance or the power cord is damaged,
▶
immediately unplug the power cord or switch off
the fuse in the fuse box.
Call Customer Service. → Page 33
▶
Repairs to the appliance should only be carried
▶
out by trained specialist staff.
Improper repairs are dangerous.
¡
Repairs to the appliance should only be carried
▶
out by trained specialist staff.
Only use genuine spare parts when repairing the
▶
appliance.
If the power cord of this appliance is damaged, it
▶
must be replaced by trained specialist staff.
Improper installation is dangerous.
¡
Connect and operate the appliance only in ac-
▶
cordance with the specifications on the rating
plate.
Connect the appliance to a power supply with al-
▶
ternating current only via a properly installed
socket with earthing.
The protective conductor system of the domestic
▶
electrical installation must be properly installed.
Never equip the appliance with an external
▶
switching device, e.g. a timer or remote control.
36
When the appliance is installed, the mains plug
▶
of the power cord must be freely accessible. If
free access is not possible, an all-pole isolating
switch must be installed in the permanent elec-
trical installation according to the conditions of
Overvoltage Category III and according to the in-
stallation regulations.
When installing the appliance, check that the
▶
power cable is not trapped or damaged.
Information on the installation
situation
Install this appliance on the kitchen ceiling or a
¡
stable suspended ceiling.
Instructions for the exhaust air pipe
The appliance manufacturer does not provide any war-
ranty for faults attributable to the pipeline.
Use a short, straight exhaust air pipe with as large a
¡
pipe diameter as possible.
Long, rough exhaust air pipes, many pipe bends or
¡
small pipe diameters reduce the suction power and
increase the fan noise.
An exhaust air pipe that is made of non-combustible
¡
material.
To prevent condensate from returning, fit the ex-
¡
haust air pipe from the appliance with a 1° gradient.
Round pipes
Use round pipes with an inner diameter of 150 mm (re-
commended) or at least 120 mm.
Flat ducts
Use flat ducts with an inner cross-section that corres-
ponds to the diameter of the round pipes:
Diameter of 150 mm corresponds to ap-
¡
prox. 177 cm².
Diameter of 120 mm corresponds to ap-
¡
prox. 113 cm².
Use sealing strips for different pipe diameters.
¡
Do not use any flat ducts with sharp bends.
¡
Instructions for the electrical
connection
In order to be able to safely connect the appliance to
the electrical system, follow these instructions.
WARNING ‒ Risk of electric shock!
It must always be possible to disconnect the appli-
¡
ance from the electricity supply. The appliance must
only be connected to a protective contact socket
that has been correctly installed.
The mains plug for the mains power cable must
▶
be easily accessible after the appliance is in-
stalled.
If this is not possible, an all-pole isolating switch
▶
must be integrated into the permanent electrical
installation according to the conditions of over-
voltage category III and according to the installa-
tion regulations.