Siemens SINAMICS S120 Manuel De Configuration page 43

Tableau de sélection et références de commande
Power Magnetizing Efficiency
factor current
η
I
μ
rated
cos ?
A
690 V 3 AC line voltage, Servo/Vector Control
0.87 34 0.923
0.86 45 0.927
0.86 57 0.930
0.85 55 0.943
0.84 80 0.947
0.84 100 0.950
0.81 91 0.955
0.80 125 0.957
0.81 145 0.959
0.86 94 0.961
0.87 105 0.963
0.86 134 0.964
4)
Output type : Vibration severity
grade:
Coupling N
Coupling R
Belt/incr. cantilever forces N
Belt/incr. cantilever forces R
Shaft extension: Balancing:
Fitted key Half-key
Fitted key Full-key
Plain shaft –
Paint finish:
Primed
Anthracite (RAL 7016), standard paint finish
Anthracite (RAL 7016), special paint finish
Special versions: Specify supplementary order code and plain text if applicable (see Options).
C30 absolutely essential
1)
n : Max. permissible thermal speed at constant output or speed,
2
which is at the voltage limit when P = P
2)
n : Max. permissible speed that is continuously permitted without
S1
speed duty cycles.
3)
n : Maximum speed which must not be exceeded.
max
Moteurs asynchrones 1PH7 (PM)
Manuel de configuration, (APH7P), 05/2007, 6SN1197-0AC71-0DP0
Rated Moment of Weight,
frequency inertia of approx.
f J
rated
2
Hz kgm / kg/lb
2
lb -in-s
f
17 4.2/37.173 1300/2866.5 1PH7284- . . B . . - 0
17 5.2/46.02 1500/3307.5 1PH7286- . . B . . - 0
17 6.3/55.76 1700/3748.5 1PH7288- . . B . . - 0
27 4.2/37.173 1300/2866.5 1PH7284- . . C . . - 0
27 5.2/46.02 1500/3307.5 1PH7286- . . C . . - 0
27 6.3/55.76 1700/3748.5 1PH7288- . . C . . - 0
38.6 4.2/37.173 1300/2866.5 1PH7284- . . D . . - 0
38.6 5.2/46.02 1500/3307.5 1PH7286- . . D . . - 0
38.6 6.3/55.76 1700/3748.5 1PH7288- . . D . . - 0
58.7 4.2/37.173 1300/2866.5 1PH7284- . . F . . - 0
58.7 5.2/46.02 1500/3307.5 1PH7286- . . F . . - 0
58.7 6.3/55.76 1700/3748.5 1PH7288- . . F . . - 0
Shaft and flange accuracy:
N
R
N
R
.
rated
1.3 Tableau de sélection et références de commande
1PH7 asynchronous motor
Order No.
7 7 7
7 7 7
7 7 7
7 7 7
7 7 7
7 7 7
7 7 7
7 7 7
7 7 7
7 7 7
7 7 7
7 7 7
A
B
E
F
A
C
J
4)
See Table "Permissible combinations of mechanical designs".
5)
The rated output current is lower than the motor rated current.
6)
Only in conjunction with option M84 (insulated version of encoder).
7)
Speed is limited to lower values in some cases. The following restric-
tion applies: Max. output frequency < 5 × motor rated frequency.
Description du moteur
SINAMICS S120 Motor Module
Rated output current
I
rated
A Order No.
85 6SL3320-1 T H28-5AA0
5)
100
6SL3320-1 T H31-0AA0
150 6SL3320-1 T H31-5AA0
120
6SL3320-1 T H31-2AA0
175 6SL3320-1 T H31-8AA0
215 6SL3320-1 T H32-2AA0
5)
175 6SL3320-1 T H31-8AA0
260 6SL3320-1 T H32-6AA0
330
6SL3320-1 T H33-3AA0
260 6SL3320-1 T H32-6AA0
5)
260 6SL3320-1 T H32-6AA0
330 6SL3320-1 T H33-3AA0
0
3
6
–Z
43