Power Regulation - EdilKamin PELLKAMIN 8 Installation, Usage Et Maintenance

Filling the cochlea.
The fi rst time you use the product, or should the tank be com-
pletely emptied of pellets, to fi ll the coclea press both keys "+"
and "–" on the remote control at the same time, holding for a
few seconds. As you release the keys, the display should show
the wording "LOAD". This should be carried out before igni-
tion if the insert has stopped due to having run out of pellets,
at the end of operation to empty the combustion pot before
turning.
It is quite normal for some pellets to remain, that the cochlea
cannot suction.
Automatic igniting.
With the insert on stand-by, press and hold the key
remote control for 2 seconds. This will start-up the
ignition procedure, showing the wording "START". At the
same time, a countdown in seconds begins (from 1020 to 0).
Ignition is not at a preset time, however: its duration is automa-
tically shortened if the board reports that certain tests have
been passed. The fl ame appears after about 5 minutes.
Manual igniting.
Temperatures of below 3°C will not allow the electrical resi-
stance to heat suffi ciently. In this case, or should the
resistance be temporarily out of action, Diavolina® type fi re-
starters can be used.
Insert a piece of lit Diavolina into the combustion chamber,
close the door and press

POWER REGULATION

• Remote control manual operation
With the insert working, press the key "M" on the remote con-
trol once. The display will show the word "POWER P".
(specifying the power at which the insert is working). Press the
keys "+" or "–" to increase or decrease the insert's
working power (from "POWER P1" to "POWER P5").
• Remote control automatic operation
Press key "A" to switch to automatic operation, adjusting the
temperature desired for the room (use the "+" and "–" keys
to set the temperature from 5°C to 35°C, and the insert will
regulate working power required to reach the temperature set.
If a temperature below that of the room is set, the insert will
stay on "POWER P1".
Turning off
With the insert running, press and hold the key
mote control for 2 seconds. The turn-off procedure will begin,
showing a countdown on the display from 9 to 0 (for a total of
10 minutes).
The turn-off phase involves:
• Interruption of pellet supply
• Maximum ventilation.
• Smoke expulsion motor.
Never pull the plug out whilst the device is still in the process
of turning off.
INSTRUCTIONS FOR USE
, on the
the remote control.
rom the re-
OPERATIONS THAT CAN ONLY BE CARRIED OUT BY
REMOTE CONTROL
Clock regulation
Press and hold the key "M" for 2 seconds to access the "Clock"
menu. This allows you to set the internal electronic board
clock. By then pressing the key "M", the following data appe-
ars in sequence and can be regulated:
day, month, year, hour, minutes, day of the week.
The wording "SAVE??" will appear for confi rmation with "M".
This will allow you to check that the operations performed are
correct, prior to completion (the wording "SAVE" will then be
shown on the display).
Weekly timer
Press and hold the "M" key on the remote control for 2 secon-
ds. This turns on the clock regulation and by pressing the '+'
key, the weekly timer function is accessed, with the display
showing the description "PROGRAMM ON/OFF".
This function allows you to set a number of times the insert
turns on and off per day (up to a maximum of three), each
day of the week.
As you confi rm the display with the key "M", one of the fol-
lowing options will appear:
NO PROG. (no programme set)
DAILY PROGRAM (single programme for every day of the
week)
WEEKLY PROGRAM. (specifi c programme for each day
individually)
Use the "+" and "–" keys to switch between programmes.
Use key "M" to confi rm the option "DAILY PROGRAM" to
choose the number of programmes (turn on/off) to be carried
out per day.
Use the "DAILY PROGRAM" to set identical programme/s for
every day of the week.
By then pressing the "+" key, the following can be seen:
- Prog. no.
- 1st prog. (one turn on and one turn off per day), 2nd prog.
(identical), 3rd prog. (identical)
Use the "–" key to show in reverse order.
If the 1st programme is selected, the turn on time is shown.
The display shows: 1 "ON" at 10 Use the "+" and "–" key to
change the hour. Confi rm with the "M" key.
The display shows: 1 "ON" at 30 Use the "+" and "–" key to
change the minutes. Confi rm with the "M" key.
The same applies for the turn-off time to be set and for subse-
quent turning on and off.
Confi rm by pressing "M" and the wording "SAVE??" will
appear on the display.y.
When confi rming "WEEKLY PROGRAM", you will need to
choose the day to which the programming is to apply:
1 Mon ; 2 Tues; 3 Wed; 4 Thurs; 5 Fri; 6 Sa; 7 Sat
Once you have chosen the day, use the "+" and "–" key and
confi rm with the "M" key, to programme in the same way as
for the "DAILY PROGRAM", choosing whether or not to ena-
ble a programme for each day of the week, and if so
choosing number of interventions and at what times.
Should you make an error during programming, you can leave
the programme without saving. As you press a key,
display will show the word "no SAVE".
- 52
-
, he