Sleep Operation - Sharp MD-E9000H Mode D'emploi

Timer and Sleep Operation (continued)
Notes:
I The timer cannot control the component connected to the auxiliary input sockets.
I When the CD or MiniDisc is over, playback will stop before the stop time.
If you wish to play to the stop time, set repeat play for the CD or MiniDisc.
Timer playback and timer recording cannot be set at the same time.
To confirm the timer setting:
1. Whilst in the timer stand-by mode, press the TIMER button.
2. Within 10 seconds, press the 5/3 or 2/4 button to select "TIMER CALL".
3. Press the MEMORY/ENTER button.
After the settings are displayed sequentially, your system will return to the timer stand-
by mode.
To cancel the timer operation:
Whilst in the timer stand-by mode, press the ON/STAND-BY button to turn the power
on. The timer operation will be cancelled.
You can also cancel the timer operation by the following steps without turning on the
power.
1. Press the TIMER button.
2. Within 10 seconds, press the 5/3 or 2/4 button to select "CANCEL".
3. Press the MEMORY/ENTER button.
Caution:
In the following cases, the timer recording function will not work.
When a MiniDisc has not been inserted.
When the MiniDisc is for playback only or protected against accidental erasure.
When there is no recording space left on the MiniDisc ("TOC FULL " or "DISC
FULL" appears).

Sleep operation

The radio, CD and MiniDisc can all be turned off automatically.
1
Play the desired sound source.
2
Press the SLEEP button.
3
Within 10 seconds, press the MEMORY/ENTER button.
4
Press the 5 5 /3 3 or 2 2 /4 4 button to select the time.
5 5 5 3 3 3 2 2 2 4 4 4
(Maximum: 2 hours - Minimum: 1 minute)
The amount of sleep time can also be changed during the sleep operation.
*07-E39-41-MD9000H(SEEG) 40
5
Press the MEMORY/ENTER button to set the sleep time.
6
The unit will enter the stand-by mode automatically after the pre-
set sleep time has elapsed.
To cancel the sleep operation:
Setting the unit to the power stand-by mode cancels the sleep operation.
You can also cancel the sleep operation by the following steps without setting the unit
to the power stand-by mode.
1. Whilst in the sleep operation, press the SLEEP button.
2. Within 10 seconds, press the MEMORY/ENTER button. "SLEEP" indicator will go
out.
To confirm the remaining sleep time:
1. Whilst in the sleep operation, press the SLEEP button.
2. Within 10 seconds, press the 5/3 or 2/4 button to select "SLEEP". The
remaining sleep time will be displayed.
After 10 seconds, the display will return to normal.
If you press the MEMORY/ENTER button whilst the remaining sleep time is dis-
played, you can change the sleep time. (Perform steps 4 and 5 above.)
Notes:
Once the sleep time is set, it will remain unchanged until a new time is entered.
The sleep functions cannot be used to control the device connected to this unit.
You must use its sleep functions, if it has them.
Simultaneous sleep and timer operation
1
Perform steps 1 - 3 of the "Sleep operation" on this page.
2
Perform steps 1 - 11 on page 39, "Timer playback/Timer record-
ing".
1 Sleep timer setting
2 Timer playback
Timer playback
(record) setting
(record) start time
1 minute - 2 hours
Sleep operation will
automatically stop.
01.4.19, 3:09 PM
MD-E9000H
Desired time
End time
E-40
D
F
S
V
I
N
E