Attachment; Using The Saw; Operation - Scheppach HS80 Traduction Du Mode D'emploi Original

8. Attachment

Prepare the workplace where you intend to place
the electrical power tool. Provide enough space
to ensure safe and trouble-free operation. The
power tool is designed for working in enclosed
rooms and has to be installed on level and firm
ground.
m IMPORTANT! Pull out the power plug before car-
rying out any maintenance, resetting or assembly
work on the circular saw!
m NOTE!: The electrical power tool is heavy - thus
two people should lift the device out of its
ASSEMBLY Saw blade cover Fig. 3
In order to assemble the saw blade cover (5), place
it above the riving knife (4), so that the screw fits into
the slit of the riving knife while loosening the attached
wing nut. (Fig.3). Then, push the saw blade cover into
the bottom of the opening. Tighten the wing nut, so
that the saw blade cover sits on the saw table (7),
but lifts itself, when the work piece is pushed towards
the saw blade. Make sure that the saw blade cover
moves back to its idle position (touching the saw ta-
ble) after you have finished cutting.
m Note!: The saw blade cover (5) has to be in work-
ing position at all times in order to avoid contact with
the saw blade.
ASSEMBLY PARALLEL STOP FIG. 10/14
Use the star grip screws (10) to mount the clamping
claws (N) to the rip fence (9) on both sides. Use the
clamping claws (N) to insert the rip fence (9) laterally
into the saw table (7).(Fig.3)
Use the star grip (10) to tighten the rip fence (9) on
both sides.(Fig.14)
ASSEMBLY MITRE GAUGE FIG. 1/9
Insert the mitre gauge (2) into the groove on the saw
table (7). Loosen the knob (M), adjust to the desired
angle and tighten the knob (M) again. You can use
the movable fence (8) of the rip fence (9) to improve
the work piece guidance by tightening the movable
fence (8) with the knobs (L) to the mitre gauge (2).
(Fig. 9)
MOUNTING TABLE EXTENSION FIG. 2/5-8
• Loosen the star grip screws (Fig.7/Pos.H)
m ATTENTION! Don´t turn out the star grip
screws too much.
• Insert the end caps (D) into the guide tubes (F) of
the table extension as shown in Fig.5. Now insert
the guide tubes (F) of the table extension (1) into
the guide sleeves (G) (see Fig. 4/6)
• Fix the table extention with the screws (E) as shown
in Fig. 6
• Fully pull out the table extension and fix with the
star grip screws (H)
• Now fold the feet of the extension to the outside
• Align the table extension to the table saw horizon-
tal (Fig.8)
For this, loosen the locknuts (J) and set the height
adjustment screw (K) accordingly. Then tighten
the locknuts (J) again.
• Table extension not in use:
- Loosen the star grip screws (H)
- Fold the feet inwards
- Insert the table extension (1) and fix it by using
MOUNTING SUCTION FIG. 1/2
• Attach the suction hose (not included) to the suc-
tion port (A) on the back side of the machine (Fig.1)
packaging. and on the guard (Fig.2).

9. Using the saw

ON/OFF SWITCH (FIG. 1 POS.15)
ADJUSTING THE CUTTING HEIGHT FIG. 11
The saw blade has to be adjusted in such a way that
the top of the highest saw tooth is slightly higher than
the work piece.
The saw blade (6) can be adjusted to the intended
cutting height by rotating the height adjustment han-
dle (12). Rotating counter clockwise enlarges the cut-
ting height, rotating clockwise reduces the cutting
height.
ADJUSTING THE ANGLE OF THE SAW BLADE
FIG. 12
Loosen the locking handle (11). You can adjust the
saw blade (6) to the intended angle on the scale (14)
by rotating the angle adjusting wheel (13). Tighten the
locking handle (11) again.
CALIBRATING THE ANGLE OF THE SAW BLADE.
FIG. 13
m ATTENTION! Pull out the main plug
The scale (14) can be calibrated during the examina-
tion of the angular accuracy of the saw. Adjust the
saw blade (6) at the very top - make sure to have
a right angle to the saw blade (6). Adjust the angle
adjusting wheel (13) in a way that the saw blade (6) is
parallel to the angle. Adjust the pointer to an angle of
0° by using the screw (P).

10. Operation

WORKING INSTRUCTIONS
• After each new adjustment it is advisable to carry out
a trial cut in order to check the set dimensions. After
switching on the saw, wait for the blade to reach its
maximum speed of rotation before commencing with
the cut.
• Secure long workpieces against falling off at the end
of the cut (e.g. with a roller stand etc.)
the star grip screws (H)
- Press the green pushbutton 'I' to switch the
saw on.
- Press the red pushbutton '0' to switch the saw off.
GB І 27 27