Scheppach HS80 Traduction Du Mode D'emploi Original page 24

3. Protect yourself from electric shock
- Avoid physical contact with earthed parts (e.g.
pipes, radiators, electric ranges, cooling units).
4. Keep children away
- Do not allow other persons to touch the equip-
ment or cable, keep them away from your
work area.
5. Securely store unused electric tools
- Unused electric tools should be stored in
a dry, elevated or closed location out of the
reach of children.
6. Do not overload your electric tool
- They work better and more safely in the speci-
fied output range.
7. Use the correct electric tool
- Do not use low-output electric tools for heavy work.
- Do not use the electric tool for purposes for
which it is not intended. For example, do not
use handheld circular saws for the cutting of
branches or logs. Do not use the electric tool
to cut firewood.
8. Wear suitable clothing
- Do not wear wide clothing or jewellery, which
can become entangled in moving parts.
- When working outdoors, anti-slip footwear is
recommended.
- Tie long hair back in a hair net
9. Use protective equipment
- Wear protective goggles.
- Wear a mask when carrying out dust-creating
work
10. Connect the dust extraction device if you
will be processing wood, materials similar to
wood, or plastics.
- If connections for dust extraction and a col-
lecting device are present, make sure that
they are connected and used properly.
11. Do not use the cable for purposes for which
it is not intended
- Do not use the cable to pull the plug out of
the outlet. Protect the cable from heat, oil and
sharp edges
12. Secure the workpiece
- Use the clamping devices or a vice to hold the
workpiece in place. In this manner, it is held
more securely than with your hand.
13. Avoid abnormal posture
- Make sure that you have secure footing and
always maintain your balance
14. Take care of your tools
- Keep cutting tools sharp and clean in order to
be able to work better and more safely.
- Follow the instructions for lubrication and for
tool replacement.
- Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
- Check extension cables regularly and replace
them when damaged.
- Keep the handle dry, clean and free of oil and
grease
24 І GB 24
15. Pull the plug out of the outlet
- During non-use of the electric tool or prior to
maintenance and when replacing tools such
as saw blades, bits, milling heads
16. Do not leave a tool key inserted
- Before switching on, make sure that keys and
adjusting tools are removed.
17. Avoid inadvertent starting
- Make sure that the switch is switched off when
plugging the plug into an outlet.
18. Use extension cables for outdoors
- Only use approved and appropriately identi-
fied extension cables for use outdoors.
19. Remain attentive
- Pay attention to what you are doing. Remain
sensible when working. Do not use the electric
tool when you are distracted.
20. Check the electric tool for potential damage
- Protective devices and other parts must be
carefully inspected to ensure that they are
fault-free and function as intended prior to
continued use of the electric tool.
- Check whether the moving parts function
faultlessly and do not jam or whether parts are
damaged. All parts must be correctly mounted
and all conditions must be fulfilled to ensure
fault-free operation of the electric tool.
- Damaged protective devices and parts must
be properly repaired or replaced by a recog-
nised workshop, insofar as nothing different is
specified in the operating manual.
- Damaged switches must be replaced at a cus-
tomer service workshop.
- Do not use any electric tool on which the
switch cannot be switched on and off.
21. ATTENTION!
- The use of other insertion tools and other ac-
cessories can entail a risk of injury.
22. Have your electric tool repaired by a qualified
electrician
- This electric tool conforms to the applicable
safety regulations. Repairs may only be per-
formed by an electrician using original spare
parts. Otherwise accidents can occur
Warning! This electric tool generates an electromag-
netic field during operation. This field can impair ac-
tive or passive medical implants under certain condi-
tions. In order to prevent the risk of serious or deadly
injuries, we recommend that persons with medical
implants consult with their physician and the manu-
facturer of the medical implant prior to operating the
electric tool.