Scheppach HS80 Traduction Du Mode D'emploi Original page 28

• Take extra care when starting the cut!
• Never use the equipment without the suction function.
• Regularly check and clean the suction channels.
Suitability of the saw blades:
- 24 teeth: soft materials, large chip depth, coarse
cut profile
- 48 teeth: hard materials, small chip depth, fine cut
profile
OVERLOAD PROTECTION
This electrical power tool is provided with an overload
protection. If the overload protection has been initi-
ated, proceed as follows:
• Disconnect the power tool from the power supply.
• Allow the power tool to cool down.
• Check the power tool carefully for possible dam-
ages.
• Have damages repaired before re-starting the pow-
er tool.
• Connect the power tool to the power supply.
• Push the reset button (16).
• Turn on the power tool as described and put it into
operation.
WORKING WITH THE RIP FENCE FIG. 14/15
The movable fence (8) has two different guide sur-
faces. Depending on the thickness of the work piece,
the movable fence for thick or thin material should
be used.
- Thick material (Fig. 14)
- Thin material (Fig. 15)
Loosen both knurled screws (Q) and pull off the mov-
able fence (8) to it. Reattach the movable fence as
required by the locating heights and tighten both
knurled screws (Q).
WORKING ON SAWING MACHINES
Cutting broad work pieces, Fig. 21
Broadness of the processed work piece: more
than 120 mm
Tool: circular saw blade for a parallel cut
Process: Adjust the parallel stop according to the in-
tended broadness of the work piece. Ensure safe and
best possible positioning of the hands. In case that
narrow work pieces are detached during the cutting
process, always use the push stick (17) in the area of
the saw blade. If there is danger that the work piece
jams between the saw blade, riving knife and paral-
lel stop, switch off the machine and move the paral-
lel stop back to the centre of the saw blade or use a
short auxiliary stop..
m NOTE!: In all our figures, the saw blade cover is
only slightly indicated (or left out completely in indi-
vidual cases) which allows a better demonstration of
the processes or the equipment. The upper suction
hood is necessary to perform the shown processes!
28 28 І GB
Cutting narrow work pieces, Fig. 22/26/28
Broadness of the processed work piece: below
120 mm
Tool: circular saw blade for a parallel cut
Process: Adjust the parallel stop according to the in-
tended broadness of the work piece. Move the work
piece forward with both hands, use the push stick in
the saw blade area and move the work piece until it
passes the push stick. When working with short work
pieces, use the push stick for the complete moving
process.
CUTTING EDGES AND BORDERS, FIG. 23
Process: Mount the parallel stop with low contact
surface or use the auxiliary stop. Use the push stick
to move the work piece forward until the end of the
work piece is located in the push stick's area. Longer
work pieces can be secured against tilting towards
the end of the cutting process by using a table exten-
sion.
m NOTE!: Equipment that requires a connection
to parts of the power tool should be fastened with
screws as screw clamps can only create temporary
connections on machines.
CROSS CUTTING NARROW WORK PIECES FIG. 24
m NOTE!: For cross cutting narrow work pieces we
recommend you to use a buffer strip which is not in-
cluded in delivery.
Tool: fine-toothed cross-section blade
Process: Adjust the buffer strip in a way that the work
piece sections cannot touch the ascending part of the
saw blade. Use the lateral stop unit or the cross lat-
eral pusher to supply work pieces.
Do not use your hands to remove scrap pieces from
the work piece area.
PARALLEL CUTS
Always use the parallel stop for performing parallel
cuts.
The rip fence (9) can be fastened on both sides of the
saw table (7).
Loosen the star grip (10).
In order to use the scale, move the stop towards the
saw blade and measure the dimension on the scale.
Then, move the stop away from the saw blade. The
dimensional difference is identical with the cutting
width. In order to guarantee a precise measurement,
it is necessary to cut a test piece, to measure the
work piece and to adjust the stop.
Move the rip fence (9) to the intended position.
Fasten the two star grip (10).
m WARNING!: The parallel stop has to be adjusted
parallel to the saw blade. Check the alignment and
ensure that the parallel stop is held firmly regularly
and especially during use and when it is not used for
a longer period of time. If necessary, re-tighten the
screw and adjust the parallel stop. Vibrations can
cause loose screws and a relocation of the parallel
stop.