Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
− Damaged guards and parts must be properly
repaired or exchanged by a recognized, specialist
workshop; insofar as nothing else is stated in the
instructions for use.
− Damaged or illegible security labels have to be
replaced.
Electrical safety
Design of the connection cable according to IEC 60
245 (H 07 RN-F) with a core cross-profile section of at
least
− 1.5 mm
2
for cable lengths up to 25 m
− 2.5 mm
2
for cable lengths over 25 m
Long and thin connection lines result in a potential
drop. The motor does not reach any longer its maximal
power; the function of the device is reduced.
Plugs and coupler outlets on connection cables must
be made of rubber, non-rigid PVC or other
thermoplastic material of same mechanical stability or
be covered with this material.
The connector of the connection cable must be splash-
proof.
When running the connection line observe that it does
not interfere, is not squeezed, bended and the plug
connection does not get wet.
Do not use the cable for purposes for which it is not
meant. Protect the cable against heat, oil and sharp
edges. Do not use the cable to pull the plug from the
socket.
Wind off completely the cable when using a cable
drum.
Regularly check the extension cables and replace
them if they are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables
especially approved and appropriately labelled for
outdoor use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current
circuit breaker (30 mA).
The electrical connection or repairs to electrical
parts of the machine must be carried out by a
certified electrician or one of our customer service
points. Local regulations – especially regarding
protective measures – must be observed.
Repairs to other parts of the machine must be carried
out by the manufacturer or one of his customer
service points.
Use only original spare. Accidents can arise for the
user through the use of other spare parts. The
manufacturer is not liable for any damage or injury
resulting from such action.
A
s
s
e
m
b
l
y
A
s
s
e
m
b
l
y
Connect chain saw to power supply system only after
having finished the complete assembly.
Risk of injury!
Wear protective gloves when assembling.
Put the chain saw with motor facing downward on an
even face.
1
Remove the cover (10) by loosening the fastening
screw (11).
1
Insert the saw chains into the circular guide slot of the
sword. Attend to the correct running direction of the
2
chain links.
Put on the sword.
When assembling, pay attention that the chain links are
lying correctly within the guide slot and on the chain
wheel (13).
4
Saw chain can hardly be put around the chain wheel?
Turn the chain clamp (22) anti-clockwise until the saw
chain can easily be put around the chain wheel. Turn
the chain clamp (22) clockwise until the saw chain is
firmly clamped.
Now, refasten the cover (10) and clamp the saw chain
as described in paragraph „Clamping of saw chain".
B
e
f
o
r
e
t
h
e
f
i
B
e
f
o
r
e
t
h
e
f
i
Chain lubrication
The chain saw is not delivered filled with saw chain
adhering oil.
The use without saw chain adhering oil results in
damages of the chain saw.
The durability and cutting power of the chain depends on
the optimal lubrication. During operation the chain saw is
lubricated automatically with oil via the oil flow canal.
Charging the oil tank:
Put the chain saw on a suitable base.
Unscrew the oil tank lock (9).
Fill the oil tank with bio-degradable chain saw adhering
oil (app. 100 ml). The fill level can be seen on the
inspection window (17). For easier filling use a funnel.
When filling observe that no dirt reaches the oil tank.
Screw on the oil tank lock again.
Once you have filled the oil tank for the first time
or after it was completely emptied press the "primer"
about 10 times to pump oil in the circuit.
Never use recycled oil or used oil. The guarantee
expires when using oil which is not allowed for chain saws.
20
3
r
s
t
c
o
m
m
i
s
s
i
o
n
r
s
t
c
o
m
m
i
s
s
i
o
n
5
i
n
g
i
n
g
Publicité
Chapitres
Table des Matières
