Ryobi EMS-1830SC Manuel D'utilisation page 31

GB
F D
SAFETY INSTRUCTIONS FOR BASIC SAW
OPERATIONS
Make sure the blade is sharp, undamaged and
■
properly aligned. With the saw unplugged, push the
power head all the way down. Hand spin the blade
and check for clearance. Tilt the power-head to
45 degree bevel and repeat the check. If the blade
hits anything, make the adjustments shown in the
Maintaining "Alignment (Adjustments)" section.
Make sure the blade and arbor collars are clean.
■
Make sure the collars' recessed sides are facing
■
the blade.
Using 6.35 mm hex end of combination wrench
■
(supplied), make sure the left hand thread arbor
screw is firmly tightened counterclockwise.
Make sure all clamps and locks are tight and there is
■
no excessive play in any parts.
Keep work area clean. Cluttered areas and benches
■
invite accidents. Floor must not be slippery. To reduce
the risk of burns or other fire damage, never use the
miter saw near flammable liquids, vapors or gases.
PLAN AHEAD TO PROTECT YOUR EYES,
HANDS, FACE AND EARS
Know your miter saw. Read and understand the
■
owner 's manual and labels affixed to the tool.
Learn its application and limitations as well as the
specific potential hazards peculiar to this tool.To
reduce the risk of injury from accidental contact with
moving parts, don't do layout, assembly, or setup
work on the miter saw while any parts are moving.
Reduce the Risk of Accidental Starting, make sure
■
switch is "OFF" before plugging miter saw into a
power outlet.
Plan your work. Use The Right Tool. Don't force tool
■
or attachment to do a job it was not designed to do.
Use a different tool for any workpiece that can't be
held in a solidly braced, fixed position.
CAUTION
Because of the sliding action of this saw,
this machine is not designed for cutting metals.
Use this miter saw to cut only wood, and wood
like products. Other materials may shatter, bind
on the blade, start fires or create other dangers.
PREPARING TO MAKE THE CUT
Inspect Your Workpiece. Make sure there are no nails
■
or foreign objects in the part of the workpiece to be cut.
E I P NL S DK N FIN
English
Plan your work to avoid thrown pieces caused when
■
the workpiece binds on the blade and is torn from
your hands.
Plan how you will make the cut.
■
Always:
Make sure the blade is not spinning.
■
Raise the blade.
■
Slide the saw out above the front edge of the
■
workpiece before starting saw, and
Push the lower guard safety lock knob (19) to release
■
the lower guard, than push the sawblade down on top
of the wood and back toward the rear of the saw to
make the cut.
DANGER
NEVER pull the saw toward you during a cut.
The blade can suddenly climb up on top of the
workpiece and force itself toward you.
Plan the way you will hold the workpiece from start to
■
finish.
BASIC SAW OPERATIONS
MAKING COMMON SLIDE COMPOUND CUTS
There are two types of cuts that can be made with the
slide compound miter saw;
Slide Cutting:
■
- The slide lock knob is left loose, the cutting head is
pulled towards the operator, the sawblade is
lowered into the workpiece and then pushed to the
rear of the saw to complete the cut.
- Used for cutting wide pieces.
Chop Cutting (Fig. 21):
■
- The slide lock knob is tightened and the saw handle
is o pushed down to cut through the workpiece.
- This type of cut is used mainly for narrow pieces.
WARNING
For your convenient use and safety, your saw
has a blade brake. The brake is not a safety
device. Never rely on it to replace proper use of
the guard on your saw. If the blade does not stop
within 6 seconds, unplug the saw and follow the
instructions in the Trouble Shooting section for
fixing the brake before using saw again.
25
GR H CZ RUS RO PL