Safety Precaution - Ryobi EMS-1830SC Manuel D'utilisation

GB
F D
THANK YOU FOR BUYING A RYOBI PRODUCT.
To ensure your safety and satisfaction, carefully read
through this OWNER'S MANUAL and SAFETY
INSTRUCTIONS before using the product.

SAFETY PRECAUTION

Before moving the saw, lock the miter, bevel, slide
■
and power head positions. Unplug the power cord.
To reduce the risk of back injury, get help when you
need to lift the saw.
Never carry the tool by the cord or power head
■
trigger handle. Damage to insulation could cause an
electric shock. Damage to wire connections could
cause a fire.
Reduce the Risk of Dangerous Environment. Use
■
the miter saw in a dry, location, protected from rain.
Keep work area well lighted.Place the saw so neither
the user nor bystanders are forced to stand in line with
the blade. Thrown debris could injure people in its path.
To reduce the risk of injury from unexpected saw
■
movement:
- Place the miter saw on a firm level surface where
there is plenty of room for handling and properly
supporting the workpiece.
- Support the miter saw so the table is level and
the saw does not rock.
- Bolt, screw or clamp the saw to its support.
Never Stand On Tool. Serious injury could occur if
■
the tool tips or you accidentally hit the cutting blade.
Do not store anything above or near the tool where
anyone might stand on the tool to reach them.
To reduce the risk of injury or death from
■
electrical shock:
- Make sure your fingers do not touch the plug's metal
prongs when plugging or unplugging the miter saw.
- This TOOL IS DOUBLE INSULATED to give you
added protection. Double insulation does not take
the place of normal safety precautions when
operating this tool. When servicing this double
insulated tool, use only identical parts.
Disconnect The Miter Saw. To reduce the risk of
■
injury from accidental starting, unplug the saw, before
changing the setup, changing the blade or adjusting
anything.Compare the direction of rotation arrow on
the guard to the direction arrow on the blade.
The blade teeth should always point downward at the
front of the saw.
Check For Damaged Parts. Check for:
■
- Proper Alignment of moving parts,
- Damaged electric cords,
E I P NL S DK N FIN
English
- Binding of moving parts,
- Broken parts,
- Stable mounting,
- Function of arm return spring and lower guard:
Push the arm all the way down, then let it rise up
until it stops by itself. Check the lower guard to see
if it closed fully. If it did not, follow the instructions in
the "Troubleshooting" section.
- Smooth, solid movement of sliding assembly.
- Other conditions that may affect the way the miter
saw works.
If any part of this miter saw is missing, bent,
■
or broken in any way, or any electrical parts don't
work, turn the saw off and unplug it.
Keep Guards In Place, in working order, and in
■
proper adjustment.
Maintain Tools With Care. Keep the miter saw clean
■
for best and safest performance. Follow instructions
for lubricating. DON'T put lubricants on the blade
while it's spinning.
Remove Adjusting Keys And Wrenches from tool
■
before turning it on.
Use Only Recommended Accessories. Consult this
■
owner's manual for recommended accessories.
Follow the instructions that come with the
accessories. The use of improper accessories may
cause risk of injury.
- Choose the right 305 mm diameter blade for the
saw and the material you plan to cut.
- Make sure the blade is sharp, undamaged and
properly aligned. With the saw unplugged, push the
power head all the way down. Hand spin the blade
and check for clearance. Tilt the power head to
45 degrees left and right bevel and repeat the check.
If the blade hits anything, make the adjustments
shown in "Alignment (Adjustments)" section.
Make sure the blade and arbor flange are clean.
■
- Make sure the flange recessed sides are facing
the blade.
- Using the 6.35 mm hex end of combination wrench
(supplied) or a 12.7 mm box end wrench, make sure
the left hand thread arbor screw is firmly tightened
counterclockwise.
- Make sure all clamps and locks are tight and there
is no excessive play in any parts.
Keep Work Area Clean. Cluttered areas and
■
benches invite accidents. Floor must not be slippery.
To reduce the risk of burns or other fire damage,
■
never use the saw near flammable liquids, vapors
or gases.
17
GR H CZ RUS RO PL